Heat & Glo SLR-X-AU Скачать руководство пользователя страница 40

Страница: 40 / 57

Heat & Glo • SLR-X-AU Installation Manual • 2493-980 Rev. B • 12/17

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas

types.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specified

and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input

pressures.

• Pressure requirements are:

WARNING! Risk of Fire or Explosion!

High pressure

will damage valve. Low pressure could cause explosion.

• Verify inlet pressures. Verify minimum pressures when

other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is

greater than 1/2 psig.

Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE

pressure testing gas line at test pressures

above 1/2 psig.

• Close the manual shutoff valve BEFORE

pressure testing gas line at test pressures

equal to or less than 1/2 psig.

WARNING

REMOVE 2 SCREWS

Figure 9.1 Base Pan Removal

Gas Pressure

Natural Gas Propane

Butane

Minimum inlet pressure

1.13 kPa

2.75 kPa 2.75 kPa

Maximum inlet pressure

3.40 kPa

3.40 kPa 3.40 kPa

Manifold pressure

.87 kPa

2.40 kPa 2.40 kPa

C. Gas Service Access

Access Through the Valve Assembly

1. Locate and remove the two screws that secure the

base pan to the appliance. See Figure 9.1. Remove

base pan. Retain screws.

Access Through the Control Cavity

The lower access cover panel is removable if finishing

material has not been previously installed. See Section

8.A for removal instructions.

NOTE:

The gas control valve supplied with this product

is approved for a maximum inlet pressure of

3.40 kPa

For pressures over

3.40 kPa

, an in line pressure regula

tor must be installed upstream from the gas control valve.

Содержание SLR-X-AU


























































Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды

Heat & Glo SLR-X-AU, Руководство по установке

Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды