Heat & Glo SLR-X-AU Скачать руководство пользователя страница 4

Страница: 4 / 57

Heat & Glo • SLR-X-AU Installation Manual • 2493-980 Rev. B • 12/17

B. Glass Specifications

This appliance is equipped with 5 mm ceramic glass. Re

place glass only with 5 mm ceramic glass. Please contact

your dealer for replacement glass.

A. Appliance Certification

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemen

tal room heat or as a decorative appliance. It should not be

factored as primary heat in residential heating calculations.

Product Specific and Important Safety Information

C. Gas Pressure Requirements

Pressure requirements for SLR-X-AU fireplaces are

shown in table below.
Two taps are provided on the right hand side of the gas

control for a test gauge connection to measure the inlet

and outlet pressures.
The fireplace and its individual shut-off valve must be dis

connected from the gas supply piping system during any

pressure testing of the system at test pressures in excess

of 3.4 kPa.
If the fireplace must be isolated from the gas supply pip

ing system by closing an individual shut-off valve, it must

be of the handle-less type.

* The allowable Outlet (Manifold) Gas Pressure ranges are: Natural Gas .80 - .95 kPa and ULPG 2.37 - 2.61 kPa.

MODEL:

SLR-X-AU

LABORATORY:

IAMPO OCEANA

TYPE:

Direct Vent Heater

STANDARD:

AS/NZS 5263.1.3:2016

Natural Gas

Propane

Butane

Inlet Gas Pressure

1.13 - 3.40 kPa

2.75 - 3.40 kPa

* Outlet (Manifold) Gas Pressure

.87 kPa

2.40 kPa

Gas Rate

.405

.134

.111

Maximum Gas Consumption

31.65 MJ/h

27.43 MJ/h

25.30 MJ/h

Burner Injector

#37 DMS (2.64 mm)

#53 DMS (1.51 mm)

.057 DMS (1.45 mm)

Pilot Injector

.023 (.584 mm)

.014 (.356 mm)

.010 (.254 mm)

The Heat & Glo gas appliances discussed in this Installer’s

Guide have been tested to certification standards and listed

by the applicable laboratories.

This appliance must be installed in accordance with the

rules in force.

Gas types only through field conversions.

Содержание SLR-X-AU


























































Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды

Heat & Glo SLR-X-AU, Руководство по установке

Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды