Heat & Glo SLR-X-AU Скачать руководство пользователя страница 1

Страница: 1 / 57

Heat & Glo • SLR-X-AU Installation Manual • 2493-980 Rev B • 12/17

Models:

Installation Manual

Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT

discard this manual!

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Leave the building immediately.
- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup

plier’s instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

DANGER

HOT GLASS

WILL

CAUSE BURNS.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

SLR-X-AU

NOTE:

NOT INTENDED FOR

FIREPLACE INSERT.

Ref No: GMK10477

AS/NZS 5263.1.3.2016

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
DO NOT MODIFY THIS APPLIANCE.

Содержание SLR-X-AU


























































Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды

Heat & Glo SLR-X-AU, Руководство по установке

Результаты поиска

Содержание SLR-X-AU

Отзывы:

Бренды по названию

Популярные бренды