background image

2635040 Rev E

01/04

RHW-56 INSTALLATION INSTRUCTIONS

I. MAINTENANCE INSTRUCTIONS

WARNING!

A chimney fire can permanently damage your chim-

ney system. This damage can only be repaired by

replacing the damaged component parts. Chimney

fires are not covered by the Limited Warranty and

Buyer Protection Plan.

Figure 27

Chimney & Termination Cap Cleaning

2. Creosote and Soot

Inspect  the  chimney  internally  for  obstructions  and

construction damage. Flue pipe joints and seams must

be continuous and mechanical tight. In a used chimney,

additional inspection is needed for creosote buildup,

which is the formation of a flammable sediment.
When wood is burned slowly, it produces tar and other

organic vapors, which combine with expelled moisture

to  form  creosote.  The  creosote  vapors  condense  in

the relatively cool chimney flue of a slow-burning fire.

As a result, creosote residue accumulates on the flue

lining. When ignited, this creosote makes an extremely

hot fire.
The chimney should be inspected at least twice a year

during  the  heating  season  to  determine  if  creosote

buildup has occurred.
If creosote has accumulated, it should be removed

to reduce the risk of a chimney fire.

3. Chimney Cleaning

If  you  do  detect  a  buildup  of  creosote,  contact  a

qualified chimney sweep or clean it yourself. To do this,

perform the following steps:

a.

Open the damper.

b.

Hang a damp sheet across the fireplace opening

to stop dirt and soot from entering the room.

c.

Remove the termination cap or housing top. See

Figure 27.

d.

Clean with a stiff nylon brush attached to a pole

OR  tie  a  small  burlap  bag  filled  with  straw  and

several small stones or sand. Work up and down

the flue until the flue is clean.

e.

Replace the termination cap or housing top.

4. Clear Space Near the Fireplace

Combustible materials must not be stored on the hearth

extension. Room furnishings such as drapes, curtains,

chairs, or other combustibles must be at least four feet

from the open front of the fireplace.

1. Disposal of Ashes

Ashes  should  be  placed  in  a  metal  container  with  a

tight-fitting lid. The closed container of ashes should

be placed on a noncombustible floor or on the ground,

well away from all combustible materials, pending final

disposal. If the ashes are disposed of by burial in soil

or otherwise locally dispersed, they should be retained

in the closed container until all embers have thoroughly

cooled.

Содержание RHW-56





























Отзывы: