Heat & Glo RHW-56 Скачать руководство пользователя страница 17

Страница: 17 / 28

01/04

35040 Rev E

RHW-56 INSTALLATION INSTRUCTIONS

Note:

Use only a noncombustible material to finish

the face of the fireplace below the level of the front

standoffs. A noncombustible material such as USG

MICORE CV230 Mineral Fiber Board, or USG

DUROCK Cement Board is recommended for this

purpose.

Figure 16 - Air Clearance Around Gas Line

CAUTION:

When using a gas log set, the fireplace damper

must be set in the fully open position. This

ensures proper venting of combustion

products.

WARNING!

This fireplace was not tested by the fireplace

manufacturer for use with an unvented gas log

heater. To reduce risk of injury, do not install

an unvented gas log heater in this fireplace un-

less it has been specifically tested and listed

by Underwriters Laboratories Inc. for use in

this specific model fireplace. Unless the

unvented gas log heater is tested and listed for

use in this factory built fireplace, a fire hazard

may be created that can result in a structure

fire.

16. Gas Log/Lighter Provisions

Knockouts are provided on both sides of the fireplace

to allow for connection of a certified gas log lighter or

a decorative gas appliance with a maximum input of

100,000 BTU/hour, incorporating an automatic gas

shutoff device and complying with the

Standard for

Decorative Gas Appliances for Installation in

Vented Fireplaces, ANSI Z21.60

. The decorative gas

appliance should be installed in accordance with the

National Fuel Gas Code, ANSI Z223.1-1980

. The side

refractories are designed to allow ½ iron pipe to pass

through. Use a noncombustible sealant to seal any

opening between the gas pipe and refractory on the

inside. Repack the insulation removed to seal around

the gas pipe where it exits the side of the fireplace. A

minimum 1½ air clearance must be provided around

the ½ iron pipe for a minimum of 4 inches beyond the

fireplace. See Figure 16.

CLEARANCES!

A minimum 1½ air clearance must be maintained

at the back and sides of the fireplace assembly

except at the nailing flange where the clearance is

½.
Chimney sections at any level require a 2 minimum

air space clearance between the framing and

chimney section.

15. Complete the Enclosure

Complete the fireplace enclosure, allowing space for

outside air ducts and gas piping if desired. Electrical

wiring should not come in contact with the fireplace.

minimum clearance of 1½ must be maintained

between the fireplace sides and the enclosure as

well as the fireplace back and the enclosure.

See

pages 9-10 for framing details.

Содержание RHW-56





























Результаты поиска

Содержание RHW-56

Отзывы:

Похожие инструкции для RHW-56

Бренды по названию

Популярные бренды

Heat & Glo RHW-56, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RHW-56

Отзывы:

Похожие инструкции для RHW-56

Бренды по названию

Популярные бренды