manualshive.com logo in svg

Heat & Glo Pier-HVB-IPI, Руководство пользователя, Страница: 3 / 40

Поделиться
Скачать
Heat & Glo Pier-HVB-IPI Скачать руководство пользователя страница 3

Heat & Glo  •  PIER-HVB-IPI, ST-HVB-IPI •  2006-901 Rev. C •  12/07

3

Safety and Warning Information .................................................. 2

Service Parts List ......................................................................... 4

Approvals and Codes .................................................................. 9

Appliance Certification ................................................................................... 9

Installation Codes .......................................................................................... 9

High Altitude Installations ............................................................................... 9

Requirements for the Commonwealth of Massachusetts .............................. 10

Getting Started ............................................................................ 11

Introducing the Heat & Glo Gas Fireplaces .................................................. 11

Pre-install Preparation ................................................................................. 11

Installing the Fireplace ............................................................... 14

Step 1.  Locating the Fireplace .................................................................... 14

Step 2.  Framing the Fireplace ..................................................................... 15

Step 3.  Installing the Vent System .............................................................. 18

A.  Vent System Approvals ......................................................... 18

B.  Installing Vent Components ................................................... 25

C.  Vent Termination .................................................................... 27

Step 4.  Positioning, Leveling, and Securing the Fireplace ........................... 30

Step 5.  The Gas Control System ................................................................ 30

Step 6.  The Gas Supply Line ...................................................................... 31

Step 7.  Gas Pressure Requirements ........................................................... 31

Step 8.  Wiring the Fireplace ........................................................................ 32

Step 9.  Finishing ......................................................................................... 35

Step 10. Installing Trim, Logs & Ember Material .......................................... 36

Installing the Trim .......................................................................... 36

Positioning the Logs ...................................................................... 36

Shutter Settings ............................................................................ 36

Glass Specifications ...................................................................... 36

Placing the Ember Material ........................................................... 37

Ember Light Bulb Replacement ..................................................... 37

Step 11.  Before Lighting  the Fireplace ........................................................ 38

Step 12.  Lighting the Fireplace ................................................................... 38

After the Installation ..................................................................................... 38

Maintaining and Servicing Your Fireplace ................................ 39

Contact Information ...................................................................................... 40

Î

 =  Contains updated information.

Table of Contents

Í

Содержание Pier-HVB-IPI









































Отзывы:

Нет отзывов