background image

1

Heat & Glo  • Grand-I35-C, Grand-I35-SP, Supreme-I30-C, Supreme-I30-SP  •  2206-901 Rev. P  •  6/14

Models:
GRAND-I35-C
GRAND-I35-SP
SUPREME-I30-C
SUPREME-I30-SP

• 

DO NOT

 store or use gasoline or other 

fl

 am-

mable vapors and liquids in the vicinity of this 

or any other appliance.

•  What to do if you smell gas   

DO NOT

 try to light any appliance.

DO NOT

 touch any electrical switch. 

DO 

NOT

 use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas suppli-

er’s instructions.

-  If you cannot reach your gas supplier, call 

the 

fi

 re department.

•  Installation and service must be performed 

by a quali

fi

 ed installer, service agency, or the 

gas supplier.

WARNING: If the information in these 

instructions is not followed exactly, a 

fi

 re 

or explosion may result causing property 
damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

Installation and service of this appliance should be 
performed by quali

fi

 ed personnel. Hearth & Home 

Technologies suggests NFI certi

fi

 ed or factory trained 

professionals, or technicians supervised by an NFI 
certi

fi

 ed professional.

•  Leave this manual with 

party responsible for use 
and operation.

DO NO

T

DISCARD

• Important operating 

and maintenance 
instructions included.

•  Read, understand and follow 

these instructions for safe 
installation and operation.

In the Commonwealth of Massachusetts installation must be 
performed by a licensed plumber or gas 

fi

 tter.

A CO detector shall be installed in the room where the appliance 
in installed.

WARNING

A barrier designed to reduce the risk of burns 
from the hot viewing glass is provided with this 
appliance and shall be installed.  

HOT GLASS 

WILL 

          CAUSE BURNS. 

DO NOT

 TOUCH GLASS 

UNTIL  COOLED.

NEVER

  ALLOW CHILDREN

TO TOUCH GLASS.

This appliance may be installed as an OEM 
installation in manufactured home (USA 
only) or mobile home and must be installed 
in accordance with the manufacturer’s 
instructions and the 

Manufactured Home 

Construction and Safety Standard,

 

Title 24 

CFR, Part 3280 

in the United States, or the 

Standard for Installation in Mobile Homes, 
CAN/CSA Z240 MH Series,

 in Canada.

This appliance is only for use with the type(s) 
of gas indicated on the rating plate. This 
appliance is not convertible for use with other 
gases, unless a certi

fi

 ed kit is used.

Содержание GRAND-I35-SP



















































Отзывы: