manualshive.com logo in svg

Heat & Glo 6000TR-OAK, Руководство пользователя

Поделиться
Скачать
Heat & Glo 6000TR-OAK Скачать руководство пользователя страница 21

Heat & Glo  •  6000TR-OAK, 6000TR-OAK-IPI  •  383-901  Rev. K  •   5/06

25

Figure 26.  Ceiling Firestop (Ceiling Side)

If the area above the ceiling 

IS

 an attic, position and secure

the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least

1 inch (25mm).

Figure 27.    Attic Firestop

JOIST

CEILING FIRESTOP

CEILING

NAILS (4 REQUIRED)

CEILING

CEILING FIRESTOP

RAFTER

NAILS (4 REQUIRED)

NOTE: There must be NO INSULATION or other

combustibles inside the framed firestop opening.

Figure 28.  Trapezoid Termination Cap

!

C.  Vent Termination

Refer to Cinch Pipe and Termination Cap installation in-

structions.

Horizontal Termination

• The termination kit should pass through the wall firestops

from the exterior of the building.

• Adjust the termination cap to its final exterior position

on the building and interlock the flue sections.

!

WARNING:  VENTING TERMINALS SHALL

NOT BE RECESSED INTO A WALL OR SID-

ING.  VENT TERMINATION CLEARANCES MUST

BE FOLLOWED TO AVOID FIRE DANGER. SEE

VENT TERMINATION MINIMUM CLEARANCES DI-

AGRAM ON FOLLOWING PAGE.

WARNING:  THE TERMINATION CAP MUST BE

POSITIONED SO THAT THE ARROW IS POINT-

ING UP.

7-1/4 in.

(184mm)

Содержание 6000TR-OAK
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды