background image

 

5

3.If unintended movement or brake release occurs, turn the powered wheelchair off as 

soon as it is safe. 

4.Be aware that adding accessories or components, or modifying the powered wheel- 

chair, may make it more susceptible to interference from radio wave sources.(Note: 

It is difficult to evaluate the effect on the overall immunity of the powered wheel- 

chair). 

5.Report all incidents of unintended movement or brake release to the powered 

wheelchair manufacturer, and note whether there is a radio wave source nearby. 

Power wheelchairs and motorized scooters (in this section, both will be referred to 

as powered wheelchairs) may as susceptible to electromagnetic interference (EMI),   

which is interfering electromagnetic energy emitted from sources such as radio 

stations, TV stations, amateur radio (HAN) transmitter, two-way radios and cellular 

phones. The interference (from radio wave sources) can cause the powered 

wheelchair to release its brakes, move by itself or move in unintended directions. It 

can also permanently damage the powered wheelchair’s control system. The inten- 

sity of the EM energy can be measured in volts per meter(V/m).Each powered 

wheelchair can resist EMI up to a certain intensity. This is called “immunity level”.   

The higher the immunity level, the greater the protec

t

ion. At this time, current 

technology is capable of providing at least 20 V/m of immunity level, which would 

provide useful protection against common sources of radiated EMI. 

Following the warnings listed below should reduce the chance of unintended brake 

release or powered wheelchair movement that could result in serious injury: 

Do not turn on hand-held personal communication devices such as citizens band (CB) 

radios and cellular phones while the powered wheelchair is turned on. 

 

TURN OFF YOUR POWERED WHEELCHAIR AS SOON AS POSSIBLE WHEN 

EXPERIENCING THE FOLLOWING:

 

‧ 

Unintentional motions 

‧ 

Unintended or uncontrollable direction. 

‧ 

Unexpected brake release

 

The FDA has written to the manufacturers of power wheelchairs asking   

them to test new products to be sure they provide a reasonable degree of immunity 

against EMI. The FDA requires that a powered wheelchair should have an immunity 

level at least 20 V/m, which provides a reasonable degree of protection against more 

common sources of EMI. The higher the immunity level, the greater the protection. 

Your powered wheelchair has an immunity level of 20 V/M which should protect 

against common sources of EMI. 

 

Содержание P16RTL


























Отзывы: