HearthStone hase lima 8150, Руководство пользователя

Страница: 12 / 31

Hearthstone Quality Home Heating Products, Inc ® Lima Model 8150
12
O
UTSIDE
A
IR
S
UPPLY
(Kit #91- 53700)
You can connect an outside air source directly to
this stove using an optional outside air kit. The
advantage of providing outside air directly to the
stove is that the air used by the stove for combustion
is taken from outside the residence rather than from
within the room where the stove is located.
The outside air kit for this stove allows for the direct
connection of the stove's air intake to a minimum 3"
(76 mm) diameter duct (supplied by others) which
leads to the outside of the house. When considering
placement of the duct from the outside of the house
to the hearth, keep in mind the need to avoid
structural members of the house. The outside air kit
will attach to the back of the stove.
The International Residential Code (IRC) does not
allow the outside air duct to terminate higher than
the appliance. Some building officials also do not
like to see any vertical rise in the duct’s termination.
Hearthstone recommends the termination be at the
same level, or lower than the air intake on the stove.
Locate the termination of the duct on the outside
wall of the home in such a manner to avoid the
possibility of obstruction by snow, leaves or other
material. Screen the termination using ¼” x ¼” mesh
rodent screen and cover it with a rain/wind proof
hood (flex pipe, outside termination, mesh, and hood
supplied by others)* Contact your dealer for
availability).
*An adaptor for 4” duct is available from Hearthstone
if needed. Kit # 90-53308.
V
ENTING
C
OMPONENTS AND
C
ONFIGURATION REQUIREMENTS

WARNING: DO NOT CONNECT THIS UNIT TO A
CHIMNEY FLUE USED BY ANOTHER APPLIANCE

Single wall connector that is 24 MSG or 25 MSG
blued steel stovepipe.

Double wall connector (close clearance pipe)
which is used with a listed, factory-
built “Type HT"
chimney or with a masonry chimney to reduce
clearances, is available from several
manufacturers, your dealer can help you choose.
Some air insulated connector pipe models
available are Simpson Dura Vent DVL and
Metalbestos DS. Security, GSW and Ameritec
also have acceptable close clearance connector
pipe.

When used in a mobile home, a spark arrester is
required. (See page 16)

The chimney connector cannot pass through a
floor or ceiling, nor any attic or roof space, closet
or similar concealed space. Where venting
requires passage through a wall or partition of
combustible construction, the installation must
conform to NFPA Code 211 or CAN/CSA - B365.

It is very important to follow minimum clearances
for chimney connectors to combustibles such as
walls and ceilings when installing the stove.
Typical chimney connector clearances are
outlined below. The single wall clearances are
generic; the double wall clearances shown are for
Simpson DuraVent DVL.

CHECK THE SPECIFICATIONS FROM THE
MANUFACTURER OF YOUR CONNECTOR.
C
OMPONENTS OF A
V
ENTING
S
YSTEM
The complete venting system consists of several
components: chimney connector, wall thimble, wall
pass-through, chimney, and liner. It is
absolutely
necessary that you install all of these components
and maintain the clearances to combustibles
discussed earlier to ensure a safe stove installation.
To protect against the possibility of a house fire, you
must properly install and constantly maintain the
venting system
. Upon inspection, immediately
replace rusted, cracked, or broken components.

The chimney connector is the stovepipe from the
woodstove to the chimney. The chimney
connector stovepipe is 6" (152 mm) diameter, 24
MSG or 25 MSG blued steel connector pipe.
Do
not use aluminum or galvanized steel pipe - they
cannot withstand the extreme temperatures of a
wood fire.

The thimble is a manufactured (or site-
constructed) device installed in combustible
walls through which the chimney connector
passes to the chimney. It keeps the walls from
igniting. You must use a wall thimble when
installing a chimney connector through a
combustible wall to the chimney.

A wall pass-through (or chimney support
package) also keeps the walls from igniting. You
must use one when connecting through a wall or
ceiling to a prefabricated chimney.

Only install this stove to a lined masonry
chimney or an approved high temperature
prefabricated residential type building heating
appliance chimney. Do not connect this stove to