HDTV Supply WolfPack Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 43

background image

Wolfpack Component Video Matrix Switchers

Connector Labels

Signal type(s)

Y, Pb, Pr

High definition component video inputs

1 - 80

High definition component video outputs over
Cat5

IR

Input for unmodulated IR control signal via
3.5mm 2 conductor plug (tip = signal)*

RS232

Serial port for control (bidirectional)

USB

USB port for control. Software is provided to setup
USB as a virtual serial port. See the Serial
Protocol and USB Driver Installation section of
this manual

AC 90-240VAC

AC power inputs (50-60Hz) via IEC320 appliance
inlet. Connect last, after all I/O cables

*Some IR repeater systems are designed to work only with their own IR
blasters, and a common

―

workaround

ǁ

is to cut these blaster cables and add a

3.5mm plug on the end. In some cases, repeater systems will have noise that
prevents signals from being decoded.

RS-232 Connection Details

The serial port is wired as a DCE device, and should be connected to a
computer‘s RS-232 port with a straight through cable. Connection to most
control systems should be with a straight through type serial cable, such as the
cable provided with the matrix switch. For the command protocols, see the
Serial Protocols section of this guide.

Pin 1 (for reference only)

Pin 2 Transmit (Data out of unit)

Pin 3 Receive (Data in to unit)

Pin 5 Ground

«
...
5
6
7
8
9
...
»

Содержание WolfPack Series












































Отзывы:

Нет отзывов

Похожие инструкции для WolfPack Series

Бренд: Idis Страницы: 2

Бренд: YEAZ Страницы: 60

Бренд: Manfrotto Страницы: 4

Бренд: TaylorMade Страницы: 5

DWSC - Vintage C

Бренд: Daikin Страницы: 57

and Vantage Pro

Бренд: DAVIS Страницы: 4

and Vantage Pro

Бренд: Davis Instruments Страницы: 4

Бренд: Datavideo Страницы: 45

Бренд: RaceChip Страницы: 12

Бренд: Waters Страницы: 21

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: Parkside Страницы: 89

Бренд: Parkside Страницы: 28

Бренд: Hobo Страницы: 7

Бренд: Pitney Bowes Страницы: 22

Бренд: My Child Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды