manualshive.com logo in svg

Haybuster ROCK-EZE H-106, Инструкция по эксплуатации и справочник по запасным частям

Поделиться
Скачать
Haybuster ROCK-EZE H-106 Скачать руководство пользователя страница 18

10

H - 1 0 6   R O C K - E Z E

O P E R A T I N G   I N S T R U C T I O N S

2.2 ADJUSTMENTS

Preliminary adjustments are made in the factory and during set up. Some adjusting
may be necessary in field.

Machine was designed for a drawbar height of 16".

Depth of Windrower inner end nearest rock wheel is adjustable in 1" increments as
shown at (H) on Page 5. of assembly instructions. Outer end is adjusted by
changing upper hair pin in rod (U) Page 8, attached to chain drive case. Lower hair
pin is designed to carry gauge wheel during transport.

Chain adjustment on outer end of Windrower is provided to level Windrower in
raised position (T) Page 8.

Adjustments on Y bracket at front of main frame is described in step 3, page 4, and
shown at (F) on Page 8, of assembly instructions.

There are three (3) adjustments on rock plate: (Not Shown).

1.

One at rear of rock wheel which allows minimum clearance between rear of
rock plate and ring on rock wheel.

2.

One at front of rock box to allow clearance between front of rock plate and
octagon hub of rock wheel.

3.

One near lower portion of rock plate to relieve pressure against carrier bracket
plate shown at (D) on Page 8, on assembly instructions.

The clearance of the kicker rotor stripper rubber is important. Bolt holes in rubber
are slotted so it may be adjusted up or down where it bolts to the rock box. Rubber
should be clear of square bars on rotor. Rubber may be turned top side down when
a new edge is required.

Содержание ROCK-EZE H-106







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды