background image

 

 

09/19 

Model TWBS.EW.H 

Page 1 of 11 

 

 

 

 

 

 

1455 Kleppe Lane 

Sparks, NV 89431-6467 

(775) 359-4712 

Fax (775) 359-7424 

E-mail

[email protected]

 

 

website

www.hawsco.com

 

 

No. 0002080380 (12) 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 

 

 

 

 
 

 

IF YOU NEED ASSISTANCE FROM OUR TECHNICAL SERVICE DEPARTMENT,  MAKE 
SURE YOU CAN IDENTIFY THIS WATER HEATER BY HAVING THE  SERIAL NUMBER. 

 

Model No. TWBS.EW.H 

 

Serial  No.   

 

 

 
 

 

INSTALLER/ CONSUMER RESPONSIBILITIES 

 

PLEASE TAKE THE TIME TO READ NOT ONLY THIS MANUAL BUT ALSO 

THE  WARRANTY CARD ENCLOSED. WARRANTY OF THIS HEATER WILL DEPEND ON 

PROPER  INSTALLATION, OPERATION, AND REQUIRED MAINTENANCE. THE 

WARRANTY SHALL BE  VOID IF THE DESIGN OR STRUCTURE OF THE WATER 

HEATER HAS BEEN ALTERED IN  ANY WAY WHATSOEVER. THE MANUFACTURER OF 

THIS WATER HEATER WILL NOT BE  LIABLE FOR ANY DAMAGES BECAUSE OF 

FAILURE TO COMPLY WITH THE INSTALLATION 

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING 

PAGES.  IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS 

RELATING TO THE 

INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR 

TECHNICAL  SERVICE DEPARTMENT: 

800-766-5612 OR CUSTOMER SERVICE 1-888-640-4297 

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING. 

WARNING 

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY ADJUSTMENTS 

TO THE UNIT ALWAYS BE SURE MAIN CIRCUIT BREAKER IS OFF TO PREVENT DANGER 

OF SERIOUS ELECTRIC SHOCK. 

Model TWBS.EW.H 

Tempered Water Blending System 

 

INSTALLATION, OPERATION 

MAINTENANCE INSTRUCTIONS 

 

Содержание TWBS.EW.H












Отзывы: