Haulotte BilJax AS2100, Руководство по сборке

Страница: 10 / 16

STEP 11 - INSTALLING FREE STANDING RAMP
A ramp should be installed at a 1” of rise to 12” of run. The height of a run is limited to 30” maximum
before a landing is required. Determine the size and location of ramp. Example: a 24” tall stage will
require a 24’ long ramp.
A) Start at top of ramp. Determine amount of decks required. If a 4’ x 4’ deck is required,
begin with it. Example: 24” tall stage = 4’ deck + 8’ deck + 8’ deck + 4’ starter ramp.
B) Pull and hold pin in the unlocked position.
C) Fully insert a ramp leg adapter in the leg socket so that it touches the bottom of the
stage deck.
D) Release pin to lock leg adapter in place.
E) Tighten the leg socket wing bolt at each corner socket (underside of stage) where a leg
adapter is installed.
F) Attach 1-3/4” sq. leg to ramp adapter with 2-3/8” snap pin. Leg length (without base
pad) is approximately 6” shorter than desired height of ramp at leg position.
10
D
E
B
lbs.
*ALL WELD FILLETS ARE TO
REV
MATERIAL SPECIFICATION
STEP 1B - 1F
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
., Archbold, Ohio. This equipment was designed with BilJax INC This drawing is the property of
ELB
BY
10-24-19
RAMP ASSY INST DWGS
DR
WEIGHT
55.74
BY
B
SCALE
FINISH
1:4
COMPLETELY FOLLOW THE JOINT
E.C.O. 'S REVISION
DATE
REV
OF PARTS JOINED.
SIZE
DWG NO. DATE
CREATED BY THE MATING SURFACES
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 1E
STEP 1B
STEP 1D
STEP 1F
lbs.
*ALL WELD FILLETS ARE TO
REV
MATERIAL SPECIFICATION
STEP 1B - 1F
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
., Archbold, Ohio. This equipment was designed with BilJax INC This drawing is the property of
ELB
BY
10-24-19
RAMP ASSY INST DWGS
DR
WEIGHT
55.74
BY
B
SCALE
FINISH
1:4
COMPLETELY FOLLOW THE JOINT
E.C.O. 'S REVISION
DATE
REV
OF PARTS JOINED.
SIZE
DWG NO. DATE
CREATED BY THE MATING SURFACES
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 1E
STEP 1B
STEP 1D
STEP 1F
F
lbs.
*ALL WELD FILLETS ARE TO
REV
MATERIAL SPECIFICATION
STEP 1B - 1F
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
., Archbold, Ohio. This equipment was designed with BilJax INC This drawing is the property of
ELB
BY
10-24-19
RAMP ASSY INST DWGS
DR
WEIGHT
55.74
BY
B
SCALE
FINISH
1:4
COMPLETELY FOLLOW THE JOINT
E.C.O. 'S REVISION
DATE
REV
OF PARTS JOINED.
SIZE
DWG NO. DATE
CREATED BY THE MATING SURFACES
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 1E
STEP 1B
STEP 1D
STEP 1F
lbs.
*ALL WELD FILLETS ARE TO
REV
MATERIAL SPECIFICATION
STEP 1B - 1F
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
., Archbold, Ohio. This equipment was designed with BilJax INC This drawing is the property of
ELB
BY
10-24-19
RAMP ASSY INST DWGS
DR
WEIGHT
55.74
BY
B
SCALE
FINISH
1:4
COMPLETELY FOLLOW THE JOINT
E.C.O. 'S REVISION
DATE
REV
OF PARTS JOINED.
SIZE
DWG NO. DATE
CREATED BY THE MATING SURFACES
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 1E
STEP 1B
STEP 1D
STEP 1F
Side One
Side Two
Side One
Side Two