background image

2

THANK YOU!

Thank you for purchasing this product. 

We work around the clock and around the globe to ensure 

that our products maintain the highest possible quality. However, in the rare case of issues during 

assembly or use of this product, please contact our Consumer Hotline at 

800-759-0977

 for immediate 

assistance before contacting your retailer. Please read the warranty information at the back of these 

assembly instructions for further details. 

ASSEMBLY TIPS

1. Find a clean, level surface to begin the assembly of your game table. We recommend that two adults

work together to assemble this game. 

You may want to carefully cut or tear the four corners of the box

so that the bottom of the box can be used as your work surface.
2.

Remove all of the contents from box and verify that you have all of the parts shown on the Parts

List before you begin assembly. 

Note: Some parts may be pre-installed or pre-assembled.

3. Some figures or drawings may not look exactly like product.
4.

When installing parts that have more than one screw or bolt, hand tighten all screws or bolts

in place before final tightening with screwdriver or wrench.

5. Electric screwdrivers may be helpful during assembly; however, please set a 

low torque 

and use

extreme caution because screws may be stripped or overtightened, resulting in damaged parts, if the

electric screwdriver’s torque is set too high.

 

IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS

IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT. 

CARE AND USE

1. This product is intended for 

INDOOR

 use only.

2. Do 

NOT

 sit, climb or lean on the game table. 

3. Do 

NOT

 drag the table when moving it, as this will damage the legs.

Содержание BG2015



























Отзывы: