HARVEY JIB W0903X, Инструкция по эксплуатации

Страница: 2 / 21

GENERAL SAFETY RULES
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will con-
siderably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, per-
sonal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury.
But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer.
REMEMBER: Your
personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not
be modified and/or used for any application other than that for which it was designed. If you have any questions rela-
tive to a particular application,
DO NOT use the machine until you have first contacted Delta to determine if it can or
should be performed on the product.
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL . Learn the
tool’s
application and limitations as well as the specific hazards
peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION . Wear safety glass-
es. Everyday eyeglasses only have impact resistant lenses;
they are not safety glasses. Also use face or dust mask if
cutting operation is dusty. These safety glasses must con-
form to ANSI Z87.1 requirements.
NOTE: Approved glass-
es have Z87 printed or stamped on them.
4. REMOVE ADJUSTING KEYS AND WRENCHES . Form
habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it
“on”.
5. KEEP WORK AREA CLEAN . Cluttered areas and bench-
es invite accidents.
6.
DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them to
rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY . All children
and visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILDPROOF
– with padlocks,
master switches, or by removing starter keys.
9.
DON’T FORCE TOOL
. It will do the job better and be
safer at the rate for which it was designed.
10. USE RIGHT TOOL .
Don’t force tool or attachment to do a
job for which it was not designed.
11. WEAR PROPER APPAREL . No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Nonslip footwear is recommended. Wear pro-
tective hair covering to contain long hair.
12. SECURE WORK . Use clamps or a vise to hold work when
practical.
It’s safer than using your hand and frees both hands
to operate tool.
13.
DON’T OVERREACH
. Keep proper footing and balance
at all times.
14. MAINTAIN TOOLS IN TOP CONDITION . Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
16. USE RECOMMENDED ACCESSORIES . The use of
accessories and attachments not recommended by Delta
may cause hazards or risk of injury to persons.
2
17. REDUCE THE RISK OF UNINTENTIONAL STARTING .
Make sure switch is in
“OFF” position before plugging in
power cord. In the event of a power failure, move switch
to the “OFF” position.
18.
NEVER STAND ON TOOL . Serious injury could occur
if the tool is tipped or if the cutting tool is accidentally con-
tacted.
19.
CHECK DAMAGED PARTS . Before further use of the
tool, a guard or other part that is damaged should be care-
fully checked to ensure that it will operate properly and per-
form its intended function
– check for alignment of moving
parts, binding of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly
repaired or replaced.
20.
DIRECTION OF FEED . Feed work into a blade or cut-
ter against the direction of rotation of the blade or cutter
only.
21.
NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF
. Don’t leave tool until it comes to a
complete stop.
22.
STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE WHEN OPERATING A POWER
TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICA-
TION.
A moment of inattention while operating power tools
may result in serious personal injury.
23. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted, connect-
ed or reconnected.
24.
THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper
dust removal. Use wood dust collection systems whenever
possible.
25.
WARNING: SOME DUST CREATED BY
POWER SANDING, SAWING, GRINDING, DRILLING,
AND OTHER CONSTRUCTION ACTIVITIES
contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals
are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other
masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those
dust masks that are specially designed to filter out micro-
scopic particles.