HARVEST H1392 Скачать руководство пользователя страница 4

Страница: 4 / 66

Safety Alertness is the Business

of everyone

Watch for this

ALERT

Symbol

It identifies potential hazards to Personal

SAFETY

and your

HEALTH

. It

points out

SAFETY

precautions

This

SAFETY

symbol means:

ATTENTION:

BE ALERT

Why is

SAFETY

Important to you?

THREE BIG REASONS:

*ACCIDENTS DISABLE AND KILL*

* ACCIDENTS COST*

*ACCIDENTS CAN BE AVOIDED*

Failure to read this Auger manual before assembling or operation of Auger is misuse of the equipment and a

needless risk to your

HEALTH

and

SAFETY

. Your life and limbs are worth keeping. Use this equipment with

care.

Symbol

Signal Words:

DANGER, WARNING, CAUTION:

The appropriate signal word for each message has been selected using the following
Guidelines below the Alert Symbol

BE ALERT!

DANGER-

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This

signal word is to be limited to the most extreme situations, typically for machine components that, for functional
purposes, cannot be guarded

Warning-

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury, and

includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices

CAUTION-

Indicates an imminently hazardous situation that, if not avoided, will result in minor or moderate injury. It

may also be used to alert against unsafe practices.

Содержание H1392



































































Результаты поиска

Содержание H1392

Отзывы:

Похожие инструкции для H1392

Бренды по названию

Популярные бренды

HARVEST H1392, Инструкция по сборке

Результаты поиска

Содержание H1392

Отзывы:

Похожие инструкции для H1392

Бренды по названию

Популярные бренды