background image

4

Installation, Operation & Maintenance Manual

SECTION 2 - INSTALLATION AND OPERATION

2.1.2 Electrical Connections

NOTE:

Review precautions in Section 1.

2.1.3 Line Voltage

Hard wire red lead and white lead to a Power 
Source to the proper voltage as indicated on the 
motor nameplate. Connect only to a source of 
constant power, not an intermittent source such 
as a fan or limit control circuit.

2.1.4 Low Voltage-Auxiliary Safety Switch

Connect the leads of auxiliary safety switch 
to  the  thermostat  control  circuit  of  the                                                                
air conditioner/furnace. This will disrupt the 
thermostat demand in a high water condition 
(

Figure 3

).

Condensate

Pump

Wire Nut

From Thermostat

Yellow

Yellow

Furnace / A.C.

Red

Whit

e

Green

Yellow

Figure 3

THERMOSTAT DEMAND DISRUPTION 
SHOULD NOT BE UTILIzED IF 

COOLING OR HEATING REqUIREMENTS ARE A NECESSITY. 
AN ALARM SYSTEM SHOULD BE USED WITH THE AUxILIARY 
SWITCH INSTEAD.

2.2 OPERATION

After proper installation, the operation of the 
HARTELL condensate pump is automatic. Water 
is collected in the reservoir and pumped out when 
the float raises to a pre-set point. As the water level 
goes down the float turns off the motor at another 
pre-set point. Under most circumstances the pump 
requires little maintenance for efficient operation. If 
a problem occurs, please refer to the maintenance 
instructions below.

Содержание PlenumPlus KL-1DG-115







Отзывы: