manualshive.com logo in svg

Harris TVS-D 660, Руководство оператора

Поделиться
Скачать
Harris TVS-D 660 Скачать руководство пользователя страница 39

INSTAL. Menu

The INSTALLATION menu serves the purpose of specifying basic transmitter settings.

Parameter

Remark

STANDARD

Selection of the transmission standard
(B/G, M, D/K, I, N, K1)

OUTPUT BAND

Selection of the output band (Band III or
Band IV/V)

NOMINAL POWER EXT.

Adjustment of the nominal output power
BIV/V: 200 mW / 500 mW
BIII: 200mW 6 HU
If an external amplifier is present, "Exciter
Power" is indicated instead of nominal
out. power.

REMOTE CONTROL

Selection of the remote interface
- no interface
- relay (only without com-unit)
- relay + RS232 (only with com-unit)
- relay + RS485 (only with com-unit)

ADDITIONAL AMPL.:
- ADDITIONAL AMPLIFIER / CTRL:

Selection of the control interface for the
additional amplifier (ABSENT /
PARALLEL / RS 485 / RCU 8600)

NOMINAL POWER EXT.

Input of the nominal output power (47 ...
80 dBm) or setup the power class of RS
485 amplifiers. This entry is not visible if
ADD. AMP. CTRL is set to ABSENT.

DETECTOR FACTOR (4V)

Input of the detector factor (47 ... 80
dBm). This entry is not visible if ADD
AMPL CTRL is set to PARALLEL.

NUMBER OF RACKS

Number of amplifier racks (only with RCU)

AGC AT

Selection of the point where the output
power is controlled (output / exciter)

BACKPORCH SYNC DELAY

Input of the backporch synchronization
delay in ns

Operator manual

TVS-D 660 LC-Display

2 - 35

Menu Operation

Содержание TVS-D 660





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды