manualshive.com logo in svg

Harper HAWK HK 4200, Руководство оператора

Поделиться
Скачать
Harper HAWK HK 4200 Скачать руководство пользователя страница 21

HK4200

Air Cleaner

• 

Make sure intake is always free of 

 debris.

• 

When engine is turned off, remove the  

 

wing bolt.

• 

Replace the air filter according to the  

 

Maintenance Schedule.

Grease Zerk Locations

PROCEDURE

1) 

Park on level ground and set park  

 brake.

2) 

Turn machine OFF.

3) 

Apply 4-5 pumps of grease to each 

 

zerk at the noted intervals listed 

 above.

To access steering cylinder, pivot the seat for-

ward by releasing the spring pins located at 

the rear of the seat as shown in the pictures 

below.

19

Air Intake

Air Filter

KINGPIN BUSHING ON EA

SIDE & CENTER PIVOT PIN 

GREASE EVERY 16 HOURS

3 ZERKS TOTAL

STEERING CYLINDER

GREASE EVERY 16 HOURS

1 ZERK ON EA END OF CYLINDER

TO ACCESS, PIVOT SEAT FORWARD

GAUGE WHEELS

GREASE EVERY 16 HOURS

1 ZERK ON GAUGE WHEEL ON EA SIDE

HOPPER DOOR CYLINDER

GREASE EVERY 50 HOURS

2 ZERKS ON EACH SIDE

HOPPER LIFT LINKAGE PINS

GREASE EVERY 50 HRS

6 ZERKS ON EA SIDE

Содержание HAWK HK 4200

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды