background image

Chipper/Shredder

R

R

Gasoline

SAFETY WARNING!

Gasoline is extremely flammable and can

be highly explosive.

Always keep a fire extinguisher near the

Chipper/Shredder during operation.

•  

Always use an approved container for  

 gasoline.

•  

Avoid open flames or sparks while 

 

doing maintenance or refueling.

•  

Never remove the fuel tank cap or add

 

gasoline when the engine is running or

 

while it is hot.

•  

Never fill the fuel tank indoors (fumes  

 

can collect).

•  

Wipe up spilled gasoline immediately.

•  

Do not store gasoline in a room with  

 

an appliance that has a pilot light, or  

 

where electrical appliances with auto- 

 

matic switches could cause sparks.

•  

Always store gasoline outside in a  

 

safety can (a can which has a flame  

 

arrestor and pressure relief valve in  

 

pour spout).

•  

Gasoline fumes are heavy and will  

 

sink to the lowest point, collecting and  

 

becoming more and more hazardous.  

 

1 part gasoline in 20 parts air will ex- 

 

plode easily and violently.

•  

Never store the equipment with gaso- 

 

line in the tank inside a building where  

 

fumes may reach an open flame or  

 

spark. Allow the engine to cool before  

 

storing in any enclosure.

Guards & Shields

•  

Keep the equipment and attachments  

 

in good operating condition.

•  

Keep all safety devices in place.

•  

Replace all worn, damaged, unusable,

 

missing or lost safety shields and   

 

guards before operating the equip- 

 ment.

Safety Decals

•  

If safety related or instructional decals

 

become illegible or are removed, re- 

 

place them immediately.

•  

If you replace parts that have decals

 

attached to them, make sure the 

  

decals are replaced with current ver- 

 

sions, and that decals are on the re- 

 

placement parts before the machine is  

 

operated again.

•  

New decals may be obtained from  

 

your local Harper Dealer.

6

Содержание 5400







































Отзывы: