Harmonic Drive CSD-2A Component Sets Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 53

background image

39

1019659 11/2014

Wave Generator up

Wave Generator vertical

Wave Generator down

Illustration 39.1

Illustration 39.2

Operating position

The required grease quantity is dependent on the gear size and the operating position. The following operating positions
“Wave Generator above” or “Wave Generator below” refer to the position of the Wave Generator in relative to the Flexspline
flange, see illustration 39.2.

Operation mainly with Wave Generator in vertical position or below

The standard grease quantity defined in table 38.1 is calculated for operating mainly with Wave Generator in vertical position or
below.

Operation mainly with Wave Generator above

If the gear is mainly operated with Wave Generator above, additional grease must be supplied above the Wave Generator, see
illustration 39.3 and table 38.1.

Illustration 39.3

If the gear is used mainly with
Wave Generator above, then
additional grease lubrication
is necessary.

Flexspline teeth

Flexspline bore

Circular Spline teeth

Wave Generator bearing

«
...
37
38
39
40
41
...
»

Содержание CSD-2A Component Sets






















































Отзывы:

Нет отзывов

Похожие инструкции для CSD-2A Component Sets

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: FJC Страницы: 2

Бренд: SAMCHULLY Страницы: 48

Бренд: Badger Meter Страницы: 16

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: Kawai Страницы: 10

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGER WERKEN Страницы: 2

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды