Harmar Mobility Highlander CPL400 Скачать руководство пользователя

Страница: 3 / 22

When You Receive the Lift

• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage

claim.

• Verify the products match that described on the packing list attached to the exterior packaging.

• Verify the contents of the package match that shown below to the right.

Specifications

Payload Capacity

750 lbs

Vertical Travel

54” – 171”

Height

77” – 197”

Foot Print

VARIES

Platform Size

36” x 54” / 36” x 60” / 42” x 60”

Input Voltage

115vac - 20a

Control Voltage

24vac or 24vdc

Platform Speed

10 ft/min

Motor

1/2hp-90vdc or 1/2hp-24vdc

Safety

• Read all instructions in this manual before installing or operating the lift.

• Do not exceed the maximum payload capacity of 750 lbs.

• Do not ride on the lift until it is anchored in place.

• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.

• Always wear eye protection while installing or servicing this product.

• Always disconnect this product from the electrical source before servicing it.

• Only use the fasteners supplied with this lift.

• Do not wear loose clothing or jewelry when working on this product.

• Do not disable any safety equipment or switches supplied with this lift.

• Stay away from all drive train components while the lift is operating.

Содержание Highlander CPL400























Результаты поиска

Содержание Highlander CPL400

Отзывы:

Похожие инструкции для Highlander CPL400

Бренды по названию

Популярные бренды

Harmar Mobility Highlander CPL400, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Highlander CPL400

Отзывы:

Похожие инструкции для Highlander CPL400

Бренды по названию

Популярные бренды