Harmar Mobility csl500 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 24

background image

HELIX:

Install Manual

24SEP2021 | 630-00063-01 REV D

16

INSTALLATION

HELIX CURVED STAIR LIFT: SECTION 3

WIRELESS REMOTE

REPROGRAMMING

The wireless controllers are shipped pre-

programmed for the seat.

Note: The remote board will beep once and the chassis

board will beep once.

If the remotes need to be re-programmed or you

have a replacement remote, do the following:

1.

On the wireless control board, press and hold

the small black button that says "pair". At the

same time, hold the up button on remotes for

three (3) seconds. This will link the board and

the remotes to your lift.

See Figures 3-46 and 3-47.

Figure 3-46

Power light

Receiving signal

light

Reset button

Pair button

Green light indicates

up or down

Figure 3-47

«
...
14
15
16
17
18
...
»

Содержание csl500

























Отзывы:

Нет отзывов

Похожие инструкции для csl500

Бренд: Gate Страницы: 6

WALKING TUTOR WT 200

Бренд: Invacare Страницы: 8

Бренд: DeVilbiss Healthcare Страницы: 32

TGR-R KP-O 3432

Бренд: Timago Страницы: 4

Бренд: HealthCo Страницы: 7

BeRollka B2 MED3102

Бренд: Decon wheel Страницы: 4

Бренд: Triumph Mobility Страницы: 6

Бренд: NRS Healthcare Страницы: 2

Бренд: Cubro Страницы: 8

Бренд: NRS Healthcare Страницы: 4

SystemRoMedic 43804002

Бренд: Direct Healthcare Group Страницы: 32

Бренд: Direct Healthcare Group Страницы: 42

DONJOY Cool TROM

Бренд: DJO Страницы: 2

Бренд: Quantum Rehab Страницы: 20

Бренд: Xray Страницы: 40

Бренд: Vela Страницы: 2

Бренд: Harmar Mobility Страницы: 8

Adapted Pie Face

Бренд: Enabling Devices Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды