background image

Anchoring the Lift

 

Anchors 

Harmar recommends securing the lift using 

the concrete anchors provided. If you 

purchase you own floor anchors they must be 

3/8” minimum of sufficient length.

 All four 

floor anchors must be installed correctly 

in accordance to their instructions. 

Step 1 

• Position the lift in its final location.

• Verify that it is level and perpendicular to its

surroundings and all running clearances are

the proper dimension.

• Shim if necessary.

Step 2 

Use the lift’s base as a template. Drill 4 holes 

into the concrete making sure that the holes 

are deep enough to accept the anchors. 

Tip: Concrete dust may have settled into 

the holes you just drilled. Use a shop 

vacuum to clean out these holes. This will 

ensure the floor anchors set correctly. 

Step 3 

Secure the lift in place by tightening the floor 

anchor bolts. 

Step 4 (800 or taller models)

 

Taller lifts must have the top of the lift 

tower anchored into a solid surface to 

ensure running clearances remain 

constant. 

There are two options for anchoring the top of 

the tower: 

1) For lifts going up to a landing such as a

deck or porch, the optional tower brace is

the preferred method.  Instructions for the

brace are packaged with it.

2) For lifts that are placed with the back of

the tower against a solid wall such as

inside of a hoistway, drilling two holes

through the top tower cross brace and

anchoring is preferred.

Anchor

 

two

 

locations

 

Содержание CPLP400

































Отзывы: