background image

When You Receive the Lift 

• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage
claim.
• Verify the products match that described on the packing list attached to the exterior packaging.
• Verify the contents of the package match that shown below to the right.

Specifications 

Payload Capacity 

 750 lbs 

Vertical Travel  

 54” – 171” 

Height  

 77” – 197” 

Foot Print 

 VARIES 

Platform Size   

 36” x 54” / 36” x 60” / 42” x 60” 

Input Voltage   

 115vac - 20a 

Control Voltage 

 24vac or 24vdc 

Platform Speed 

 10 ft/min 

Motor   

 1/2hp-90vdc or 1/2hp-24vdc 

Safety 

• Read all instructions in this manual before installing or operating the lift.
• Do not exceed the maximum payload capacity of 750 lbs.
• Do not ride on the lift until it is anchored in place.
• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.
• Always wear eye protection while installing or servicing this product.
• Always disconnect this product from the electrical source before servicing it.

• Do not wear loose clothing or jewelry when working on this product.
• Do not disable any safety equipment or switches supplied with this lift.

Stay away from all drive train components while the lift is operating.

O

nly use the fasteners supplied with this lift.

Содержание CPLP400

































Отзывы: