Harman VF3000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 32

background image

24

3-90-70741R13_05/13

wiring diagram & Fuel

Anthracite coal is “hard coal”, mined primarily in the northeast United States. Rice coal, as shown at right, is typically

described as coal having no dimension larger than 3/8”. Other size coal may cause feeding problems, and is therefore not

recommended for use in your VF3000.
It is best to buy your supply of coal when the temperature is above freezing. This is because many dealers put kerosene

or fuel oil on the truck box and calcium on the coal to keep it from freezing while it is being transported. The calcium can

promote rust and the oil may cause an odor depending on what type is used.
It is best and most convenient to have a coal bin inside and close to the boiler. The bin should have drainage to allow the

water to drain.

dO nOt

store fuel within the specified clearance area.

Rice Coal

approved For use with anthracite rice Coal Only.

Coal

«
...
22
23
24
25
26
...
»

Содержание VF3000

































Отзывы:

Нет отзывов

Похожие инструкции для VF3000

Бренд: Adveco Страницы: 108

Бренд: Riello Страницы: 44

Бренд: Glow-worm Страницы: 40

ELTHERM M Series

Бренд: green ecotherm Страницы: 34

Бренд: LK Страницы: 10

Бренд: THERMOROSSI Страницы: 21

Bosky Boffing 6

Бренд: THERMOROSSI Страницы: 27

ECOTHERM H20 14

Бренд: THERMOROSSI Страницы: 38

Paramount five 115

Бренд: Potterton Страницы: 156

Бренд: Flexiheat Страницы: 72

Бренд: Westinghouse Страницы: 89

Бренд: THERMEx Страницы: 20

Бренд: THERMEx Страницы: 20

Бренд: THERMEx Страницы: 24

24kW Baykan Starplus

Бренд: GasTech Страницы: 26

SZM A PLUS 16 kW

Бренд: SOLZAIMA Страницы: 87

Бренд: SOLZAIMA Страницы: 105

Бренд: Potterton Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды