Harman Studer Vista FX Скачать руководство пользователя

Страница: 47 / 56

Vista FX

Vista FX 1-31

Document generated: 28.08.14

SW V4.9

5.6.6

resonance

For the category

Resonance (Resonant Chords)

the following parameters are available.

Delay Level :

Controls all delays in the algorithm. Each voice has its nominal gain value

adjusted by this percentage. [0 .. 100] %

Delay Feedback :

Controls all delays in the algorithm. Each voice has its nominal feedback gain

adjusted by this percentage. Range [0 .. 100] %.

Delay Time :

Controls all delays in the algorithm. Each voice has its nominal delay time

adjusted by this percentage. Range [0 .. 100] %

Resonance Master :

Controls all voices in the algorithm. Each voice has its nominal resonance

adjusted by this percentage. Range [0 .. 100] %

Resonance Frequency :

This parameter determines at which frequency the delay voice resonates.

Range [C0 .. B7] music note.

On mono engines only.

5.6.7

reverse

For the category

Reverse

the parameters of the Room category are available, with one additional

parameter :

Reverb Shelf :

This parameter allows a certain amount of unfiltered audio to be combined

with the filtered audio. This effectively lowers the effect of the filter. Another

way of looking at it is that it lessens the normal filter slope of 12 dB per octave.

Range [Off .. 0.0] dB.

On mono and stereo engines only.

Содержание Studer Vista FX

























































Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды

Harman Studer Vista FX, Руководство по эксплуатации

Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды