background image

 6

v

venting

requirements for Terminating the venting

wArNINg:

 Venting terminals must not be recessed 

into a wall or siding.

NOTE:

 Only pellet vent pipe wall pass-throughs 

and fire stops should be used when venting through 

combustible materials.

NOTE: 

Always take into consideration the effect  the 

prevailing wind direction or other wind currents will 

cause  with  flyash  and  /or  smoke  when  placing  the 

termination.

In addition, the following must be observed:

A. The clearance above grade  must be a minimum 

of 18".

1

B. The clearance to a window or door that may be 

opened must be a minimum of 48".

1

(

with outside air installed, 18”

)

C. A 12"  clearance to a permanently closed window  

is  recommended to prevent condensation on the 

window.

D. The vertical clearance to a ventilated soffit located 

above the terminal within a horizontal distance of 

2 feet (60 cm) from the center-line of the terminal  

must be a minimum of 18".

E. The clearance to an unventilated soffit  must be a 

minimum of 12".

F. The clearance to an outside corner is 11" from center 

of pipe.

G. The clearance to an inside corner is 12".

H.  A vent must not be installed within 3 feet (90 cm)  

above a meter/regulator assembly when measured 

from the horizontal center-line of the regulator.

1

I. The clearance to service regulator vent outlet must 

be a minimum of 6 feet.

1

J. The clearance to a non-mechanical air supply inlet to 

the building or the combustion air inlet to any other 

appliance must be a minimum of 48”.

1

K. The clearance to a mechanical air supply inlet must 

be a minimum of 10 feet.

1

(

with outside air installed, 6 feet 

)

L. The clearance above a paved sidewalk or a paved 

driveway located on public property must be a 

minimum of  7 feet.

1,2

M. The clearance under a veranda, porch, deck or 

balcony must be a minimum of 12 inches.

1,3 

(see b.)

NOTE:

  The clearance to vegetation and other exterior 

combustibles such as mulch is 36” as measured from 

the center of the outlet or cap. This 36” radius continues 

to grade or a minimum of 7 feet below the outlet.

1

Certain Canadian and or  Local codes or regulations 

may require different clearances.

2

A vent shall not terminate directly above a side-walk 

or paved driveway which is located between two 

single  family dwellings and serves both dwellings.

3

Only permitted if veranda, porch, deck, or balcony is 

fully open on a minimum of  2 sides beneath the floor.

NOTE: where passage through a wall, or partition of 

combustible construction is desired, the installation 

shall conform to CAN/CSA-b365. (if in  Canada)

Vent terminal

Содержание P61

























Отзывы: