background image

26

1 POWER INDICATOR

This LED lights to show when power is connected to the console.

2 PHANTOM POWER

Many professional condenser mics need PHANTOM POWER, which is a method of  sending a powering voltage 
down the same wires as the mic signal.  Press the switch to enable the +48V power to all of the MIC inputs.  
The adjacent LED illuminates when the power is active.

WARNING: TAKE CARE when using unbalanced mics which may be damaged by the phantom power 
voltage.  Balanced dynamic mics can normally be used with phantom power switched on (contact 
your microphone manufacturer for guidance). Mics should always be plugged in, and all output faders 
set to minimum before switching the Phantom Power ON to avoid damage to external equipment.

2-TRACK

3 2-TRACK IN

These two RCA phono sockets are unbalanced Left and Right line-level inputs, used for connecting a playback 
device. 

4 2-TRACK LEVEL CONTROL

This adjusts the signal level from the 2-Track inputs. 

5 2-TRACK TO MIX

Press this switch to route the 2-Track input signals to the MIX Left/Right bus. The level is set with the 2-Track 
level control.

MONITOR SOURCE

The following two switches select the signal source(s) to be monitored. 

6 MIX/SUB

Press  this  switch  down  to  monitor  the  sub-group  outputs.  Release  this  switch  to  monitor  the  main  mix  
outputs.

7 2-TRACK

Press this switch to monitor the 2-Track input signal.

MONITOR OUT

8 MONITOR OUTPUT LEVEL

This control sets the signal level fed to the MONITOR LEFT & RIGHT outputs.

9 MONITOR OUTPUTS

The Monitor Outputs are on 3-pole 6.35mm (1/4”) jacks and are balanced.

10 HEADPHONES LEVEL

This control sets the level of the Headphone output.

11 HEADPHONES SOCKET

The PHONES output is a 3-pole 6.35mm (1/4”) jack, wired as a stereo output, ideally for headphones of 
32

 or greater.  8

 headphones are not recommended.

Содержание MPMi























































Отзывы: