background image

 

RUSH™ MH 8 Mini Profile User Manual 

31

 

Construction 

Color ......................................................................................................... Black 
Housing .......................................... High impact flame retardant thermoplastic 
 IP rating ................................................................................................... IP 20 

Installation 

Mounting points ......................................................... Bracket  for rigging clamp 
Location ................ Dry location only, must be fastened to surface or structure 
Orientation .................................................. Vertical (head down if suspended) 
Minimum distance to illuminated surfaces ................................ 200 mm (8 in.) 
Minimum distance to combustible materials ............................. 100 mm (4 in.) 
Minimum clearance around fans and vents .............................. 100 mm (4 in.) 

Connections 

AC power input ............................................................................................ IEC 
DMX data in/out ........................................................ 3-pin  &  5-pin locking XLR 

Electrical 

AC power ............................................................ 100-240 V nominal, 50/60 Hz 
Power supply unit ................................... Auto-ranging electronic switch mode 
Fuse ...................................................................................................... T 2.0 A  

Typical power and current 

120 V, 60 Hz ................................................................................... 52 W, 0.8 A 
230 V, 50 Hz ................................................................................... 50 W, 0.5 A 
Typical half-cycle RMS inrush current...................................................... 6.4 A 

Measurements made at nominal voltage with all LEDs at full intensity. Allow 
for a deviation of +/- 10%. 

Thermal 

Cooling ...................................................... Forced air (temperature-regulated) 
Maximum ambient temperature (T

a

 max.) ................................. 40° C (104° F) 

Minimum ambient temperature (T

a

 min) .......................................... 0°C (32° F) 

Total heat dissipation* ................................................................... 180  BTU/hr. 

*Calculated, +/- 10%, at full intensity, full white 

Approvals 

  

    

     

EU safety ....................... EN 60598-2-17 (EN 60598-1), EN 62471, EN 62493  
EU EMC .................. EN 55015; EN 55032; EN 55103-1,-2; EN 61000-3-2,-3; 
 

EN 61000-4-2, -4, -5; EN 61547 

US safety ............................................................................................. UL 1573 
US EMC ............................................................. CFR Title 47 Part 15 Class A 
Canadian safety ................................................................ CSA C22.2 No. 166 

Содержание Martin RUSH MH 8 Mini Profile





































Отзывы: