16
N
0
519 AUDIO PLAYER
/
OWNER’S MANUAL
SETTINGS MENU
SETTINGS MENU
SETUP MENU NAVIGATION
Pressing the Settings button displays the Settings menu on the
№ 519’s front-panel display. When the Settings menu is active…
• use the Volume/Value knob to scroll through options,
• use the Select button to select and deselect options,
• use the Volume/Value knob to adjust parameters,
• to move back a level in the menu structure, press the
Back button repeatedly until the desired menu is shown
in the display,
• to exit the Settings menu, press the Settings button.
• Use Previous and Next to move horizontally when entering
letters and numbers.
SETTINGS
•
Volume & Balance: This menu allows you to adjust the
volume and balance of the output channels
o
Balance: use this setting to pan the output to the
left or right channel.
o
Max Volume Level: adjust this setting to limit the
maximum volume output from the № 519.
o
Mute Volume Level: adjust this setting to change
the volume level the № 519 goes to when muted.
o
Turn-On Volume Level: when turning on, the № 519
will be set to this volume level.
o
Phones Turn-On Vol: when turning on, the № 519
headphone output will be set to this volume.
o
Last Volume as Turn-On Volume Level: When this
option is checked, the № 519 will save the output
and headphone volume levels when the unit is
put into standby, maintaining them when the unit
is powered up next time. Note that the Turn-On
Volume Level and Phones Turn-On Vol settings are
disabled when this option is enabled.
o
Output Volume: this setting toggles the Balanced
and Single-Ended outputs between Variable and
Line (fixed level) modes.
Variable: use this setting when you have
connected the Balanced or Single-ended
outputs to an external preamplifier, amplifier,
or powered loudspeakers. The output level
will vary with the level of the volume control.
Line (Fixed): use this setting when you have
connected the Balanced or Single-ended
outputs to a recording device. The outputs
will remain at a fixed level regardless of the
volume control level.
Note: the Headphone output is always
Variable.
•
Operation: This menu controls the operation of the № 519
o
Power Management
Standby: this setting lets you set the Standby
mode to one of the following options: Green,
Power Save, and Normal.
•
Green:
This mode removes power from
almost all of the circuits, allowing the №
519 to be activated only via an IR control
signal, a 5V – 12V trigger or a press of
the Standby button.
This mode provides
maximum power conservation and is
the factory-default Standby mode.
•
Power Save:
This mode removes power
from the audio circuits, but keeps the
control and streaming circuitry powered
and ready to receive commands from
either the front panel controls or the
remote control. This mode provides
moderate power conservation.
•
Normal:
This mode shuts off the display
and mutes its audio outputs, but keeps
all of its control, streaming, and audio
circuits powered. This mode provides
the least amount of power conservation
but allows the audio circuits to
remain warmed up to deliver optimal
performance at all times.
Auto Off: this setting lets you engage or
disengage the Auto Off function, which puts
your № 519 into the Standby mode after 20
minutes of inactivity (no audio signal, and no
control input).
o
Remote Control
Trigger: (Normal/Pulsed) This setting
configures how the 12V trigger relay data
is sent and received. Most components
require this to be set at “Normal,” but some
products (such as some older Mark Levinson
components) require that it be set to Pulsed.
Front IR: this toggle allows you to turn the №
519’s front IR receiver on or off. If you have
connected the № 519’s rear-panel IR input to
an IR control device, set the Front IR receiver
to Off to avoid interference.
Содержание Mark Levinson 519
Страница 1: ...AUDIO PLAYER OWNER S MANUAL N0 519...
Страница 2: ......