background image

4

IMPORTANT SAFETY INFORMATION

ELECTROMAGNETIC

COMPATIBILITY

 

This device complies with part 15 of the FCC Rules and the 

Product specifications noted on the Declaration of Conformity. 

Operation is subject to the following two conditions:

•   this device may not cause harmful 

interference, and 

•   this device must accept any interference received, including 

interference that may cause undesired operation.  

Operation of this unit within significant 

electromagnetic fields should be avoided.

•  use only shielded interconnecting cables.

U.K. MAINS PLUG WARNING

A molded mains plug that has been cut off from the cord is 
unsafe. Discard the mains plug at a suitable disposal facility. 
NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT 
A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER 
SOCKET. Do not use the mains plug without the fuse cover in 
place.  Replacement fuse covers can be obtained from your local 
retailer.  Replacement fuses are 13 amps and MUST be ASTA 
approved to BS1362.

If you want to dispose this product, do not mix it with gen-

eral household waste. There is a separate collection system 

for used electronic products in accordance with legislation 

that requires proper treatment, recovery and recycling.

Private household in the 25 member states of the EU, in Switzerland 

and Norway may return their used electronic products free of charge to 

designated collection facilities or to a retailer (if you purchase a similar 

new one).

For Countries not mentioned above, please contact your local authorities 

for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes the 

necessary treatment, recovery and recycling and thus prevent potential 

negative effects on the environment and human health.

MAGNETIC FIELD

CAUTION!  Do not locate sensitive high-gain equipment such as preamplifiers 

or tape decks directly above or below the unit. Because this amplifier has a 

high power density, it has a strong magnetic field which can induce hum into 

unshielded devices that are located nearby. The field is strongest just above 

and below the unit.

If an equipment rack is used, we recommend locating the amplifier(s) in 

the bottom of the rack and the preamplifier or other sensitive equipment 

at the top.

All manuals and user guides at all-guides.com

Содержание JBL CSMA 180

































Отзывы: