background image

 19

2.6 Wiring Your Audio System

Typical input and output wirings are shown in Figure 2.6. 

INPUTS: Connect input wiring for both channels using either the RCA or the 
Euroblock input for each channel.

OUTPUTS:  You may use either low impedance or high impedance speakers.  
Always be sure to maintain the proper polarity when wiring speakers.

Low Impedance Speakers should be driven using the +/- pins of the amplifier output 
connector.  The minimum impedance an amplifier channel can drive is 4 Ohms.  
Therefore, you can connect up to four 16 Ohm speakers, two 8 Ohm speakers or one 
4 Ohm speaker to an amplifier output channel.

High Impedance Speakers should be driven using the appropriate (70V or 100V) pin 
to speaker (+) and the COM pin to speaker (-) of the amplifier output connector.  The 
minimum impedance that can be driven from each output is provided in Appendix 
A.  Note that the HI-Z switch must be ON in order to provide audio to the high 
impedance outputs.

WARNING:  Do not connect to both low impedance speakers and high impedance 
speakers from the same audio output channel. 

Figure 2.6 Wiring Audio System

Professional audio system

AUX OUT

CSR-V ONLY

Hi-Z PHANTOM

CH3 INPUT

CH4 INPUT

CH2 INPUT

CH1 INPUT

100V 70.7V COM

MIC

LINE

MIC

LINE

MIC

LINE

MIC

LINE

MONO SUM

MONO SUM

VOX

MONO SUM

100-240 V~ 50/60Hz     40W

CS

M

A 11

20

MADE IN MALAYSIA

CAUTION - TO REDUCE THE RISK 

OF ELECTRIC SHOCK, GROUNDING 

OF THE CENTER PIN OF THE PLUG 

MUST BE MAINTAINED.

5028384

AMP OUT

CLASS 2

WIRING

CH2-4 IN / AUX OUT

PRIORITY

CD                /OPTICAL

SPK   1 + 2   VIRTUAL

LEVEL

CSR-V

All manuals and user guides at all-guides.com

Содержание JBL CSMA 180

































Отзывы: