Harman AMX DXLINK DX-RX-4K Скачать руководство пользователя

Страница: 3 / 91

Hardware Reference Manual – DXLink™ Twisted Pair 4K Transmitters/Receivers

WARNING

: This product is intended to be operated ONLY from the voltages listed on the back panel or the recommended, or

included, power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to

the product and void the products warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be

plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord,

use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational

voltage, please contact your local distributor and/or retailer.

EU COMPLIANCE INFORMATION

WEEE NOTICE

US FCC COMPLIANCE NOTICE – CLASS A

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in

accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own

expense.

US FCC AND CANADA EMC COMPLIANCE INFORMATION:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

CANADA ICES INFORMATION

ICES (Interference-Causing Equipment Standard): CAN ICES-3 (A)/NMB-3(A)

LICENSE NOTICES AND TRADEMARK ACKNOWLEDGMENTS

Windows

and Internet Explorer

are registered trademarks of Microsoft Corporation in the United States and other countries.

and the UL logo are trademarks of UL LLC.

Ethernet

is a registered trademark of the Xerox Corporation.

ENERGY STAR

is a registered trademark of the U.S. Department of Energy and the U.S. Environmental Protection Agency.

Other products mentioned herein may be the trademarks of their respective owners.

Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2014/35/EU; European Union EMC Directive

2014/30/EU; European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; European Union WEEE

(recast) Directive 2012/19/EU; European Union Eco-Design Directive 2009/125/EC; European Union Registration, Evaluation,

Authorization and Restriction of Chemicals (REACH) Directive 2006/121/EC.
You may obtain a free copy of the Declaration of Conformity by visiting http://www.amx.com/techcenter/certifications.asp.

This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment

(WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate

facility to enable recovery and recycling.

Содержание AMX DXLINK DX-RX-4K




























































































Результаты поиска

Содержание AMX DXLINK DX-RX-4K

Отзывы:

Похожие инструкции для AMX DXLINK DX-RX-4K

Бренды по названию

Популярные бренды

Harman AMX DXLINK DX-RX-4K, Справочник по аппаратуре

Результаты поиска

Содержание AMX DXLINK DX-RX-4K

Отзывы:

Похожие инструкции для AMX DXLINK DX-RX-4K

Бренды по названию

Популярные бренды