Harman Allure50 Скачать руководство пользователя страница 20

Страница: 20 / 24

Harman® • Allure50 Installation Manual_R2 • 2016 - ___ • 09/16

3-90-888000i

Inspect appliance and components for

damage. Damaged parts may impair safe

operation.
•  Do NOT install damaged components.
•  Do NOT install incomplete components.
•  Do NOT install substitute components.
Report damaged parts to dealer.

I. Fire Safety

To provide reasonable fire safety, the following should be

given serious consideration:
• Install at least one smoke detector and CO detector on

each floor of your home. The National Fire Protection

Association (NFPA), recommends one Smoke Alarm on

every floor, in every sleeping area, and in every bedroom.

• Locate smoke detector away from the heating appliance

and close to the sleeping areas.

• Follow the smoke detector manufacturer’s placement and

installation instructions and maintain regularly.

• Conveniently locate a Class A fire extinguisher to contend

with small fires.

• In the event of a hopper fire:

• Evacuate the house immediately.
• Notify fire department.

J. Inspect Appliance & Components

• Remove appliance and components from packaging

and inspect for damage.

• Report to your dealer any parts damaged in shipment.

•

Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit.

WARNING

•   Installation and use of any damaged appliance.
•   Modification of the appliance.
•   Installation  other  than  as  instructed  by  Hearth  &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all

components.

• Do NOT Overfire.

Or any such action that may cause a fire hazard.

Fire Risk

Hearth & Home Technologies disclaims

any responsibility for, and the warranty will

be voided by the following actions:

WARNING

Содержание Allure50

























Результаты поиска

Содержание Allure50

Отзывы:

Похожие инструкции для Allure50

Бренды по названию

Популярные бренды

Harman Allure50, Руководство по установке

Результаты поиска

Содержание Allure50

Отзывы:

Похожие инструкции для Allure50

Бренды по названию

Популярные бренды