Harman Kardon AVR 7300 Скачать руководство пользователя страница 27

Страница: 27 / 158

To enter a station into the memory, first tune the sta-
tion using the steps outlined above. Then:

1. Press the

Memory Button

on the remote;

the station’s frequency will flash.

2. Within five seconds, press the

Numeric Keys

corresponding to the memory location where you
wish to store this station’s frequency. Once entered,
the preset number will appear in the

Upper

Display Line

3. Repeat the process after tuning any additional

stations to be preset.

Recalling Preset Stations

• To manually select a station previously entered in

the preset memory, press the

Numeric Keys

for the desired station’s memory location.

• To manually scroll through the list of preset stations,

press the

Preset Stations Selector Button

on the front panel or remote.

Recording

In normal operation, the audio or video source
selected for listening through the AVR 7300 is sent to
the record outputs. This means that any program you
are watching or listening to may be recorded simply
by placing machines connected to the outputs for

Tape Outputs

∂

Video 1/Video 2 Outputs

π∆

in the record mode.

When a digital audio recorder is connected to the

Digital Audio Outputs

œß

, you are able

to record the digital signal using a CD-R, MiniDisc or
other digital recording system.

NOTES:

• The digital outputs are active only when a digital sig-

nal is present, and they do not convert an analog
input to a digital signal, or change the format of the
digital signal. In addition, the digital recorder must
be compatible with the output signal. For example,
the PCM digital input from a CD player may be
recorded on a CD-R or MiniDisc, but Dolby Digital
or DTS signals may not.

• The

Front-Panel Video 5

jacks may be con-

figured for use as an output, allowing connection to
a recorder, when the steps shown in the section
below are followed.

• Please obey the copyright restrictions on any mate-

rial you copy. Unauthorized duplication of copyright-
ed materials is prohibited by law.

Front-Panel Connections

In addition to the rear-panel digital and analog outputs,
the AVR 7300 offers Harman Kardon’s exclusive con-
figurable front-panel output-jack feature. For easy con-
nection of portable devices, you may switch the front-
panel

Video 5 Jacks

from an input to an output

by following these steps:

1. Press the

OSD Button

to view the

MASTER MENU

(Figure 1).

2. Press the

Set Button

to enter the

IN/OUT SETUP

menu (Figure 2).

3. Press the

Navigation Button

so that the

on-screen

➔

cursor is next to

VIDEO 5

4. Press the

Set Button

and then press the

‹

›

Navigation Button

so that the word

OUT

is highlighted.

5. Press the

Set Button

to enter the change.

6. Press the

OSD Button

to exit the menus and

return to normal operation.

Once the setting is made, the

Input/Output Status

Indicator

will turn red, indicating that the jacks

are now an output, instead of in the default setting as
an input. Once changed to an output, the setting will
remain as long as the AVR 7300 is turned on, unless
the setting is changed in the OSD menu system, as
described above. However, once the AVR 7300 is
turned off, the setting is cancelled. When the unit is
turned on again, the front-panel jacks will return to
their normal default setting as an input. If you wish
to use the jacks as an output at a future time, the
setting must be changed again using the OSD menu
system, as described above.

Output Level Trim Adjustment

Normal output level adjustment for the AVR 7300 is
established using the test tone, as outlined on pages
29–30. In some cases, however, it may be desirable to
adjust the output levels using program material such as
a test disc, or a selection you are familiar with.
Additionally, the output level for the subwoofer can only
be adjusted using this procedure.

To adjust the output levels using program material, first
set the reference volume for the front left and front right
channels using the

Volume Control

)rî

If you are using a disc with test signals or an external
signal generator as the source used when the output
levels are being trimmed, you may use the remote as
an SPL meter to guide you to the correct level set-
tings. To use the EzSet remote as an SPL meter, follow
the instructions on page 29.

Once the reference level has been set, press the

Channel Select Button

and

FRONT L

LEVEL

will appear in the

Lower Display Line

. To change the level, first press the

Set Button

, and then use the

⁄

Navigation Button

to raise or lower the level. DO NOT use the vol-

ume control, as this will alter the reference setting.

Once the change has been made, press the

Set

Button

and then press the

⁄

Navigation

Button

to select the next output-channel location

that you wish to adjust. To adjust the subwoofer level,
press the

⁄

Navigation Button

until

WOOFER LEVEL

appears in the

Lower Display

Line

or on-screen display.

Repeat the procedure as needed until all channels
requiring adjustment have been set. When all adjust-
ments have been made and no further adjustments
are made for five seconds, the AVR 7300 will return to
normal operation.

The channel output for any input may also be adjusted
using the full-OSD on-screen menu system. First, set
the volume to a comfortable listening level using the

Volume Control

. Then, press the

OSD

Button

to bring up the

MASTER MENU

(Fig. 1). Press the

Navigation Button

until

the on-screen

➔

cursor is next to the

CHANNEL

ADJUST

line. Press the

Set Button

activate the

CHANNEL ADJUST

menu (Fig. 13).

Once the menu appears on your video screen, first
use the

⁄

Navigation Button

to move the

on-screen

➔

cursor so that it is next to the

TEST

TONE

line. Press the

‹

›

Navigation Button

so that

OFF

is highlighted. This will turn off the test

tone and allow you to use your external test disc or
other source material as the reference. Then, use the

⁄

Navigation Button

to select the chan-

nels to be adjusted. At each channel position, use the

‹

›

Navigation Button

to change the output

level. Remember, the goal is to have the output level
at each channel be equal when heard at the listening
position.

If you wish to reset all the levels to their original factory
default of 0dB offset, press the

⁄

Navigation

Button

so that the on-screen cursor is next to

the

CHANNEL RESET

line and press the

‹

›

Navigation Button

so that the word

highlighted. After the levels are reset, resume the
procedure outlined above to reset the levels to the
desired settings. When all adjustments are done, press
the

⁄

Navigation Button

to move the on-

screen

➔

cursor so that it is next to

BACK TO

MASTER MENU

and then press the

Set Button

if you wish to go back to the main menu to

OPERATION