Harman Kardon AVR 300 Скачать руководство пользователя страница 11

Страница: 11 / 40

REMOTE CONTROL FUNCTIONS

Remote Control Functions

IMPORTANT NOTE:

The AVR 300’s remote may

be programmed to control up to eight devices,
including the AVR 300. Before using the remote,
it is important to remember to press the

Device

Control Selector

button

b c

that

corresponds to the unit you wish to operate. In
addition, the AVR 300’s remote is shipped from
the factory to operate the AVR 300 and most
Harman Kardon CD or DVD players and cassette
decks. The remote is also capable of operating a
wide variety of other products using the control
codes that are part of the remote. Before using
the remote with other products, follow the
instructions on pages 27–29 to program the
proper codes for the products in your system.

It is also important to remember that many of
the buttons on the remote take on different
functions, depending on the product selected
using the Device Control Selectors. The descrip-
tions shown here primarily detail the functions
of the remote when it is used to operate the
AVR 300. (See page 29 for information about
alternate functions for the remote’s buttons.)

Command Indicator:

This LED lights

briefly when a button is pushed to confirm that an
infra-red (IR) commande is being sent by the
remote.

AVR Selector:

Pressing this button will

switch the remote so that it will operate the
AVR’s functions. If the AVR is in the Standby
mode, it will also turn the AVR on.

CD/DVD Input Selectors:

Pressing one

of these buttons will perform three actions at
the same time. First, if the AVR is not turned on,
this will power up the unit. Next, it will select
the source shown on the button as the input to
the AVR. Finally, it will change the remote con-
trol so that it controls the device selected. After
pressing one of these buttons you must press
the

AVR Button

again to operate the

AVR’s functions with the remote.

Power-Off Button:

Press this button to

place the unit in the Standby mode. Note that
this will turn off the main room functions, but
if the Multiroom system is activated, it will
continue to function.

Sleep Button:

Press this button to place

the unit in the Sleep mode. After the time
shown in the display, the AVR 300 will auto-
matically go into the Standby mode. Each press
of the button changes the time until turn-off in
the following order:

Press and hold the button for two seconds to
turn off the Sleep mode setting.

Note that this button is also used to change
channels on your TV when the TV is selected
using the

Device Control Selectors

Surround Mode/TV Channel

Selectors:

Press this button to begin the

process of changing the Surround mode. After
the button has been pressed, use the

⁄

but-

tons

to select the desired surround mode.

(See page 21 for more information.) Note that
this button is also used to tune channels when
the TV is selected using the

Device Control

Selector

. When the AVR 300 remote is

being programmed for the codes of another
device, this button is also used in the “Auto
Search” process. (See page 27 for more infor-
mation on programming the remote.)

Channel-Select Button:

This button is

used to start the process of setting the AVR 300’s
output levels to an external source. Once this
button is pressed, use the

⁄

buttons

select the channel being adjusted, then press the

Set

button

, followed by the

⁄

buttons

again, to change the level setting. (See page 25
for more information.)

⁄

Buttons:

These are multipurpose

buttons. They will be used most frequently to
select a surround mode. To change the surround
mode, first press the

SURR/CH

button

Next press these buttons to scroll up or down
through the list of surround modes that appear in
the

Information Display

.. These buttons are

also used to increase or decrease output levels
when configuring the unit with either the inter-
nal test tone or an external source. They are
also used to enter delay time settings after the

Delay

button

has been pressed.

Set Button:

This button is used to enter

settings into the AVR 300’s memory. It is also
used in the setup procedures for delay time,
speaker configuration and channel output level
adjustment.

‹

Button:

This button is used to change

the menu selection or setting during some of
the setup procedures for the AVR.

Digital Select:

Press this button to assign

one of the digital inputs

d e

to a source.

(See page 23 for more information on using
digital inputs.)

6-Ch. Direct Inputs:

Press this button to

select the component connected to the 6-Ch.
direct Input

as the source

Input Selectors:

Press one of these but-

tons to select one of the video inputs or the
tape input as the source for the AVR. Pressing
one of these buttons when the AVR 300 is in
the Standby mode will also turn the unit on.

Tuner Mode:

Press this button when the

tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so that the

AUTO

indicator

goes

out, pressing the

Tuning

buttons

will

move the frequency up or down in single-step
increments. When the FM band is in use, press-
ing this button when a station’s signal is weak
will change to monaural reception, as indicated
by the

MONO

indicator

. (See page 24 for

more information.)

Memory Button:

Press this button to enter

a radio station into the AVR 300’s preset memory.
After pressing the button the

MEMORY

indicator

will flash; you then have five seconds to

enter a present memory location using the

Numeric Keys

. (See pages 24–25 for

more information.)

Numeric Keys:

These buttons serve as a

ten-button numeric keypad to enter tuner preset
positions. They are also used to select channel
numbers when

has been selected on the

remote, or to select track numbers on a CD,
DVD or LD player, depending on how the
remote has been programmed.

OSD Button:

Press this button to view the

on-screen displays.

Macro 1–2 Buttons:

These buttons are

used to recall or enter the programming
sequence for a preprogrammed Macro
sequence. (See page 28 for more information
on programming and using Macros.)

Direct/Macro 3 Button:

This button has

two functions. Pressing it when the tuner is in
use will start the sequence for direct entry of a
station’s frequency. After pressing the button
simply press the proper

Numeric Keys

select a station. This button may also be used to
store or recall a macro sequence. (See pages
24–25 for more information on the tuner, and
page 28 for more information on programming
and using Macros.)

min