Harken T2701B Скачать руководство пользователя страница 2

A

B

C

Curved Track Limitations

Cars will not roll on curved track if the radius is under the minimum listed below. A shorter car can 

roll on a smaller radius. Refer to the chart below and make sure the radius is equal to, or greater  

than the radius listed for the car. To find the radius go to www.harken.com.

Track for Unsupported Spans

Harken high-beam track is designed for unsupported spans.  
The length of span depends on the load on the car. The higher 
the car load, the less span the track can handle. If the car is  
sized correctly, car length determines the spanning capability. 
Longer, high-load (HL) cars require shorter spans because  
the loads are so much greater. See track-spanning chart in  
track instructions or at www.harken.com.

Stand-up toggle

Soft 

attachment post

Stand-up toggles

 – Harken stand-up toggles fit  

specifc Harken blocks. To determine mainsheet  

block compatibility, see 4501 instructions online:

www.harken.com/manuals

Soft attachment (T2705B, T2705B.HL)

 – To attach  

loops or straps, remove stop screws and push  

attachment post out. Assemble post using blue  

Loctite

®

 adhesive on screws.

Attaching Mainsheet and Control Blocks

Radius*

*Applies to vertical  

and horizontal bends

Mid-boom 

End-boom

SPAN (inches/meters)

SAIL AREA (feet

2

/meters

2

)

Monohulls Only

R27 mm High-beam  

track spanning chart

Car

Minimum radius

ft

m

1624, 1626, 1628, 1635,T2701B, 

T2702B, T2703B, T2721B,  

T2731B, T2741B, T2705B

8

2.44

1625, 1627, 1629, 1636, T2701B.HL, 

T2702B.HL, T2703B.HL, T2721B.HL, 

T2731B.HL, T2741B.HL, T2705B.HL

9

2.73

Part No.

A

B

C

in mm in mm in mm

Low-profile track

1602.6, 1602.8, 1602.12,  

R27.1, R27.1.2, R27.1.5M, 

R27.1.8, R27.2.M, R27.2.5M, 

R27.3M, R27.3.6M, R27.6M

1

1

/

16

27

9

/

16

14

1

25

High-beam track

R27HB.1, R27HB.1.5M, 

R27HB.1.8M, R27HB.2.5M,  

R27HB.3.6M

1

1

/

16

27 1

5

/

8

42 1

7

/

32

31

Track Compatibility

CB cars are shipped for use on CB track with grooves at waist to accept retaining clips first supplied 

by Harken in 2002. See end of manual if you have older track. 

Grooves for  

retaining clips.

CB Track

1602, R27

High-

beam

A

B

C

Installing CB Traveler Car on Track

Position car at end of track and gently roll on. Car should roll on easily. If not, check to make sure 

you are using CB track. 

Do not remove ball retaining clips.

 Cars will not roll unless they have 

retaining clips. 

Exception: CB+ cars can convert to non-CB cars. See end of manual.

R27HB

Loctite is a registered trademark of Henkel AG & Company KGaA.

Содержание T2701B






Отзывы: