background image

INSTALLATION SPECIFICATIONS 

 

BTU Ratings and Pressure Requirements  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Fireplace Dimensions and Clearances 

 

Refer to the following charts to determine the proper size set for your fireplace. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

LOG SET SIZE 

 

GAS TYPE 

MAX. HEAT INPUT 

MIN. HEAT INPUT 

 

GAS INLET PRESSURE 

MAX. 

MIN. 

 

REGULATOR PRESSURE

 

22” SETS 

 

Natural 

 

Propane 

32,000 BTU/Hr. 

32,000 BTU/Hr. 

24,000 BTU/Hr. 

23,500 BTU/Hr. 

 
 
10.5 ins. WC   

13 ins. WC 

5 ins. WC 

 

11ins. WC 

 
 
4 ins. WC 

 

10 ins. WC 

 

26” SETS 

 

Natural 

 

Propane 

40,000 BTU/Hr. 

33,000 BTU/Hr. 

29,000 BTU/Hr. 

23,500 BTU/Hr. 

 
 
10.5 ins. WC   

13 ins. WC 

5 ins. WC 

 

11 ins. WC 

 
 
4 ins. WC 

 

10 ins. WC

 

 

When operating the main burner, use the control knob to raise and lower the min. and max. heat output.  Turn 
the control knob counterclockwise for max. heat and clockwise for min heat. 

Input ratings are shown in BTU per hour and are 
for elevations up to 2,000 feet.  For elevations 
above 2,000 feet, input ratings should be reduced 
4% for each 1,000 feet above sea level.  Refer to 
the National Fuel Gas Code. 

WARNING:

  OPERATION OF THIS 

APPLIANCE ON GASES FOR WHICH IT IS 
NOT EQUIPPED MAY LEAD TO CARBON 
MONOXIDE POISONING. 

 
 
 
 
 

Depth 

 
 
 
 
 

 

         

Front Width 

Log Set 

Size 

 

22” 

 
 

26” 

 

Depth 

 

12” 

 
 

12” 

 

Height 

 

16” 

 
 

16” 

Front 

Width 

 

28” 

 
 

30” 

Fireplace Dimensions 

The chart above indicates the minimum 
fireplace dimensions for each log set. 

Содержание Timberland Glow
























Отзывы: