Hardlife Utility C4040 Скачать руководство пользователя страница 2

 

SPECIFICATION 

 

Width:12m                  Length:12m              Height:4.5m 

 

IMPORTANT-----READ MANUAL FIRST 

 

Improper  site  preparation,  Assembly  and  Maintenance  may  invalidate  warranty  and  cause 
unnecessary and costly mistake. If you have any questions contact your local dealer. 
 
For User Friendly assembly we have identified each individual component with the part code as 
indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem 
free assembly. 
 
It

s  necessary  to  tighten  the  roof  fabric  enough  to  avoid 

hammocks

  on  the  roof  and  also 

re-tighten  once  or  twice  again  after  a  few  months  of  use.  This  is  important  when  assembly  in 
cold weather (autumn and winter) because the  fabric  is stiff then and when we got the sun and 
warm weather afterwards  it will  make the fabric 

slack

 again and need to  be re-tighten before 

next winter. 
 
It

s the owners responsibility to take of snow immediately if not slide off by itself.   

 

READ ALL INSTRUCTIONS BEFORE ASSEMBLY 
 

1.

 

Keep  work  area  clean.  Cluttered  areas  invite  injuries.  Do  not  set  up  near  snow  drifts,  in 
slippery places, in high winds, or wet location. 

2.

 

Keep children away. All children should be kept away from the work area. 

3.

 

Don

t over reach. Keep proper footing and balance at all times. 

4.

 

Do  not  assemble  in  under  the  influence  of  alcohol  or  drugs.  Read  warning  labels  on 
prescriptions  to  determine  if  your  judgment  or  reflexes  are  impaired  while  taking  drugs.  If 
there is any doubt, do not assemble. 

5.

 

Be  aware  of  possible  windy  conditions;  fasten  the  bases  in  concrete  if  these  conditions  are 
likely to occur. Remove the cover during hurricane. 

6.

 

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not 
expose to open flame. 

7.

 

Be  aware  of  personal  safety  during  assembly  and  use.  Be  careful  not  to  pinch  fingers  with 
clips  and  tubes  when  assembling:  when  using  makes  sure  there  is  adequate  ventilation  for 
exhaust and other dangerous fumes. 

 

 
 
 
 
 
 
 
 
 
 
 
 

Содержание C4040









Отзывы: