background image

SPECIFICATION

C2020H : Width: 6m Length: 6m

Height: 2m

C2040H : Width: 6m Length: 12m

Height: 2m

IMPORTANT-----READ MANUALFIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and
cause unnecessary and costly mistake. If you have any questions contact your local
dealer.

For User Friendly assembly we have identified each individual component with the
part code as indicated in the parts list. Please refer to the part code numbers and
drawing to ensure problem free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and
also re-tighten once or twice again after a few months of use. This is important when
assembly in cold weather (autumn and winter) because the fabric is stiff then and
when we got the sun and warm weather afterwards it will make the fabric “slack”
again and need to be re-tighten before next winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READALL INSTRUCTIONS BEFOREASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow

drifts, in slippery places, in high winds, or wet location.

2. Keep children away. All children should be kept away from the work area.

3. Don’t over reach. Keep proper footing and balance at all times.

4. Do not assemble in under the influence of alcohol or drugs. Read warning labels

on prescriptions to determine if your judgment or reflexes are impaired while

taking drugs. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricane.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch

fingers with clips and tubes when assembling: when using makes sure there is
adequate ventilation for exhaust and other dangerous fumes.

Содержание C2020H












Отзывы:

Похожие инструкции для C2020H