Hardi Navigator 3100 Скачать руководство пользователя страница 78

Страница: 78 / 104

6 - Maintenance

1000 hours service - Wheel bearings

Check the condition of the bearings in the following way:

Place stop wedges in front of and behind LH wheel and jack up RH
wheel.

Support the trailer with axle stands.

Remove the wheel.

Unscrew the 4 Allen bolts and remove the hub cap (A), cotter pin
(B) and castle nut (C).

Pull off the wheel hub assembly (D). Use a wheel puller if necessary.

Remove roller bearings (E), clean all parts in degreasing detergent
and dry them. Inspect bearings (E) and replace if necessary.

Pack bearings (E) with fresh wheel bearing grease and re-install
using a new seal (F).

Turn the wheel and tighten the castle nut (C) until a slight
resistance in the wheel rotation is felt.

Loosen the castle nut until the first notch (horizontal or vertical) is
aligned with the cotter pin hole on the shaft.

10.

Fit a new cotter pin and bend it.

11.

Fill the hub cap with fresh grease and re-attach it onto the hub.

12.

Repeat the procedure on the LH wheel.

ATTENTION! The shaft has a vertical and an horizontal cotter pin hole. Use the one first aligned with the notch when
loosening the castellated nut.

WARNING! If you do not feel totally confident changing wheel bearings, contact your HARDI® dealer’s workshop.

Содержание Navigator 3100









































































































Результаты поиска

Содержание Navigator 3100

Отзывы:

Похожие инструкции для Navigator 3100

Бренды по названию

Популярные бренды

Hardi Navigator 3100, Руководство оператора

Результаты поиска

Содержание Navigator 3100

Отзывы:

Похожие инструкции для Navigator 3100

Бренды по названию

Популярные бренды