Hardi Navigator 3100 Скачать руководство пользователя страница 71

Страница: 71 / 104

6 - Maintenance

Lubrication & Oiling Plan - Trailer/ParaLift™

Greasing the Pump

The pump is greased as follows:

•

Factory greased:

10 oz. (300 grams) grease into each lubrication point (A).

•

Normal operation:

Grease every 50 hours with 1 oz. (30 grams) of grease into
each lubrication point (A). See “50 hours service - Greasing
the pump” on page 74.

•

After disassembling the pump (diaphragm replacement, etc.):

Grease with 7 oz. (200 grams) of grease into each lubrication
point (A).

ATTENTION! In order to prevent excessive wear, it is important to
use a recommended lubricant! See “Recommended lubricants”
on page 67.

ATTENTION! The pump MUST be stopped during greasing!

Содержание Navigator 3100









































































































Результаты поиска

Содержание Navigator 3100

Отзывы:

Похожие инструкции для Navigator 3100

Бренды по названию

Популярные бренды

Hardi Navigator 3100, Руководство оператора

Результаты поиска

Содержание Navigator 3100

Отзывы:

Похожие инструкции для Navigator 3100

Бренды по названию

Популярные бренды