manualshive.com logo in svg

Hardi FTZ Force Boom, Руководство оператора и по техническому обслуживанию, Страница: 27 / 35

Поделиться
Скачать
Hardi FTZ Force Boom Скачать руководство пользователя страница 27

Boom hydraulic system continued

Fault 

    Possible 

cause    Suggested 

action

Oil heats up in Closed    

 

By-pass valve does not close properly.   

Check bypass valve

Centre 

systems.         operation. 

     Internal 

leaks 

in 

fl 

ow 

regulator. 

  Replace 

fl 

ow 

regulator 

 

           O-rings 

and 

back-up 

 

 

 

 

 

 

 

 

 

 

 

 

rings. 

           Replace 

fl 

ow 

 

 

           regulator.

Individual ram does not move.   

Blocked restrictor. 

 

 

 

Dismantle and clean  

           restrictor.

Boom 

slow/erratic. 

  Air 

in 

system. 

    Loosen 

ram 

coupling 

 

           and 

bleed 

hydraulic 

 

           system.

 

 

 

 

 

Fold speed adjustment.   

 

 

See page  4. 2 and      

 

           5. 

5 

this 

manual.

     Insuffi 

cient 

hydraulic 

pressure. 

 

  Check 

out-put 

 

 

           pressure 

of 

 

tractor 

 

           hydraulics. 

Should 

be 

 

           minimum 

of 

130 

bar.

     Tractor’s 

hydraulic 

fl 

uid 

low. 

  Check 

and 

correct 

if 

 

 

 

 

 

 

 

 

 

 

 

 

low.

Ram not functioning. 

 

 

Restrictor or regulator valve blocked.  

 

Support the boom 

with 

 

           appropriate 

rigging 

             

and 

service 

the 

             

suspect cylinder.

Further information

For further information please contact your local HARDI dealer, or visit our web site at 

www.hardi.com.au

Troubleshooting

6. 2

6 - Troubleshooting

Содержание FTZ Force Boom




































Отзывы:

Нет отзывов