background image

PREVENTATIVE MAINTENANCE GUIDE

        FOR MANUAL HOSPITAL CRIBS 

The intent of this document is to provide health care facility engineers, maintenance personnel and 
other health care professionals involved in the operation and maintenance of manual cribs made 
by Hard Manufacturing the comprehensive information needed to achieve their expected 9 year 
service life.   

1.0  General Operation

CAUTION

1.1

 Please refer to the caution pages earlier in this manual for information on the safe 

operation of one of our electric cribs.

1.2

 If a crib is damaged in any way that poses a safety issue to either the patient or sta

  

utilizing it, we recommend that 

it be removed from service and subjected to a complete       

preventive maintenance inspection. A checklist of suggested items to review is on the 
following pages of this document.

1.3

 General overall cleaning with mild non-abrasive detergent should be applied at least once 

(1) per year or at the discretion of your facility. See more detailed cleaning instructions on a
separate page of this manual.

Revised 2020.1  3.31.2020

2.0  Crib Safety Audit 

2.1 Filler Bar Spacing

 – Examine the spacing between bars of all cribs in service.  If a crib 

has railing spaces that exceed 2-3/8”, remove it from service. 

2.2 Entrapment in cribs

 – Examine the spaces between the mattress support and head, foot 

and side rails, with the mattress both 

fl

 at and in a raised position.  If the opening exceeds 4”, 

remove the crib from service.

2.3 Mattress Fit

 – Inspect your crib mattresses to determine whether they are of adequate size. 

The mattress should 

fi

 t snug within the rails and there should not be any sizeable gaps between 

the mattress and the rails.

2.4 Crib Weld Assembies

– Thoroughly inspect head and foot ends, side rails, the mattress 

platform and any other metal components of the crib frame for bent components, cracks or 
breaks. Remove from service immediately if any of this type of damage is found.

We recommend the preventative maintenance checklist provided be performed once per year 
per crib at minimum.

If a crib is damaged in any way that poses a safety issue to either the patient or sta

  utilizing 

it, we recommend that it be removed from service and subjected to a complete preventative 
maintenance inspection. A checklist of suggested items can be found below and the following pages.

29

Содержание HI-LO 1813

































Отзывы: