background image

Page 7

SKU 97728

For technical questions, please call 1-800-444-3353.

UnpAckIng

When unpacking, check to make sure 

that the item is intact and undamaged.  If 

any parts are missing or broken, please 

call Harbor Freight Tools at the number 

shown throughout the manual as soon as 

possible.

This air tool may be shipped with a 

• 

protective plug covering the air inlet.  

Remove this plug before set up.

TOOl SET Up & ASSEMblY

Read the EnTIRE IMpORTAnT 

SAFETY InFORMATIOn 

section at the beginning of this 

manual including all text under 

subheadings therein before set 

up or use of this product.

note:

  For additional information regarding 

the parts listed in the following pages, 

refer to the Assembly Diagram near 

the end of this manual.

components and controls

Assembly

A male Quick Connector (not 

1. 

included) must be installed prior to 

operating the Air Router.  To do so:

Wrap about three inches of pipe 

• 

thread sealer tape (not included) 

around the threads of the Quick 

Connector.  Then screw the Quick 

Connector firmly into the Air Inlet 

(14) of the tool.  

(See Figure A.)

To install a 1/4” Router Bit (not 

2. 

included) into the Air Router:

Firmly grasp the Housing (1) and 

• 

the Housing Cap (30), turning them 

in opposite directions.  Completely 

unwind and separate the two items.
Use the 3/4” Spanner Wrench (34) 

• 

and 9/16” Spanner Wrench (35) to 

loosen the Collet Nut (29).
Insert the Router Bit fully into the 

• 

Collet (28).
Firmly tighten the Collet Nut, 

• 

using the Spanner Wrenches. 

(See Figure b.)

 

RETAInER (26)

cOllET (28)

cOllET nUT (29)

3/4”

SpAnnER

WREncH

(34)

9/16””

SpAnnER

WREncH

(35)

FIgURE b

Содержание Central Pneumatic 97728















Отзывы: