background image

SKU 99621 

For technical questions, please call 1-800-444-3353. 

Page 3

9. 

Wear thick jeans and 

steel-toed work boots to 

help prevent injury 

caused by flying debris. 

Stay alert - Watch what you are 

10. 

doing. Use common sense. Do not 

operate ATV Spreader when you are 

tired.

11. 

Do not grasp the exposed 

turning Plate (16) edges 

when picking up or hold-

ing the Spreader.

Do not use in Rain, or damp loca-

12. 

tions.
All visitors should be kept at a dis-

13. 

tance from work area.

When servicing use only identical 

14. 

replacement parts.
Store Idle ATV Spreader Indoors, out 

15. 

of reach of children.
Maintain ATV Spreader With Care.  

16. 

Follow instructions for lubrication. 

Check for damaged parts.  If anything 

irregular is found, the damage should 

be properly repaired by a qualified 

technician unless indicated else-

where in this manual.

Disconnect the AtV Spreader when 

17. 

not in use and/or before servicing.

Specific Safety Rules

Care must be taken when lifting this 

1. 

ATV Spreader so as not to cause 

equipment damage and/or personal 

injury.
Remove any material in Hopper As-

2. 

sembly (8) before removing this ATV 

Spreader from the vehicle. 

Never attempt to install this ATV 

3. 

Spreader to the ATV vehicle alone.  

Have another adult assist when at-

taching or detaching.
Refer to the material packaging, or 

4. 

bag safety instructions when handling  

all materials to be applied with this 

Spreader.
Before attaching this ATV Spreader, 

5. 

consideration must be given to the 

load capacity of the vehicle to be 

loaded.  Be sure to account for the 

weight of this Spreader and the 

weight of the material being spread. 
Maintain labels and nameplates on 

6. 

the appliance.  These carry important 

safety information.  If unreadable or 

missing, contact Harbor Freight Tools 

for a replacement.
The warnings, precautions, and in-

7. 

structions discussed in this instruction 

manual cannot cover all possible con-

ditions and situations that may occur. 

It must be understood by the operator 

that common sense and caution are 

factors which cannot be built into this 

product, but must be supplied by the 

operator.

 SAVE tHESE 

inStRuctionS.

SPEciFicAtionS

Hopper 

Assembly 

Capacity

80 LB. Weight capacity.

1900 cu. in. Storage capacity

Drive Motor

12V Electric

Содержание 99621









Отзывы: