background image

6

ASSEMBLY INSTRUCTIONS

 

4.

6. Remove shade screws (H) from underside of 

cage (G) and carefully lower shade (F) and 
cage (G) and set aside for later use. Remove 
and discard plastic inserts.

A

G

F

6

Hardware Used

x 2

Machine Screw

BB

Attach mounting strap (B) to outlet box (not included) 

using the existing washers and outlet box screws or 

the machine screws (BB). 

NOTE:

 If the outlet box 

screws required for your outlet box are of a different 

size than the machine screws (BB), consult with a 

licensed electrician before proceeding.

Tighten machine screws (BB) completely to secure 

mounting strap (B) to outlet box.

Turn crossbar on mounting strap (B) so the screws 

(D) are level horizontally. [Use a level (not included) 

to adjust screws (D) parallel with floor and ceiling as 

needed.] Tighten preassembled set screw, located in 

the middle of the mounting strap (B), to secure 

crossbar.

      

CAUTION:

 

The fixture must be mounted to an 

outlet box that is supported by the building structure 

and can support the weight of the fixture. Plastic 

outlet boxes are not recommended.

H

Temporarily place fixture (A) over mounting 

strap (B) to determine amount of adjustment 

necessary for screws (D); screws (D) should 

come through holes in fixture (A) just enough so 

decorative nuts (C) will fit flush against fixture 

(A) when mounted. 

Once screws (D) are adjusted, use pliers (not 

included) to tighten nuts (E) on screws (D) until 

nuts (E) touch mounting strap (B).

5.

5

Outlet Box

B

A

C

D

E

H

Outlet Box

D

B

4

Crossbar

BB

BB

Содержание WL136MW











Отзывы: