HARBEN 4018 DSK Скачать руководство пользователя страница 6

Страница: 6 / 55

1.2. Introduction

Please ensure that you read this Operation & Maintenance Manual in conjunction with the

Health & Safety Manual before operation.

Within this manual, the health and safety risks are highlighted with specific symbols. These

will be referenced to sections within the Health and Safety Manual which you are required to

read. The sections to refer to in the manual will be labelled at the end of the highlighted

statement (Ex. H&S Section 2). There are three symbols that will be used to differentiate the

levels of severity. They are as follows:

: This is the symbol for



. This means that if an accident were to happen,

it would cause minor to moderate injury.

: This is the symbol for



This means that if an accident were to happen,

it could result in a serious injury or possible death.

: This is the symbol for



. This means that if an accident were to happen,

it will result in death or serious injury. This will only be shown for the most extreme

cases.

It is imperative that these symbols are paid attention to as to avoid any sort of injury.

Notices

Carefully read the notices of this manual because they give important information concerning

safe installation, use and maintenance; familiarise yourself with the workings of the machine

to rapidly switch it off and eliminate pressure.

This manual is an integral and essential part of the product; it will be consigned to the user to

ensure the training/information for personnel.

The manufacturer does not assume responsibility for damage caused to persons, things or to

the machine, in the case of improper use. Carefully preserve this manual for any further

consultation.

Identify the model of your machine by reading the details on the identification plate. Upon

delivery, inspect the machine / accessories for any damage, which may occur during transport.



CAUTION



Always follow the recommended operating procedures. Do not misuse the

equipment as this could result in injury or mechanical breakdown!

Содержание 4018 DSK
























































Результаты поиска

Содержание 4018 DSK

Отзывы:

Бренды по названию

Популярные бренды

HARBEN 4018 DSK, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 4018 DSK

Отзывы:

Бренды по названию

Популярные бренды